Recent content by Baltik

  1. Baltik

    Navien 240a2 - cant set time and date

    Seemingly stupid problem but quite frustrating if i want to set a recirculating schedule. When i set time and date in settings - then return to it it's always back to initial 2000-00-00. I did a factory reset and went through initial setup again but no avail, time and date wont stick. Anyone...
  2. Baltik

    Navien npe 240 pressure relief valve leaking

    the tank is adjustable at 50psi - would it make sense to try 75 while i wait to source a gauge? also where should said gauge be hooked up?
  3. Baltik

    Navien npe 240 pressure relief valve leaking

    I have a 150psi pressure relief valve and a small expansion tank (http://zilmetusa.com/Thermal-ZEP1) I noticed some wetness around the relief valve and went ahead and replaced it. However the same activity is happening, small water releases from the pressure relief valve after use. Is this...
  4. Baltik

    Offset toilet flange for 4” cast iron pipe?

    ok, feels like I'm finally getting my head around this with everyone's help, i confirmed using a magnet that i have lead on the outside. So I guess that leaves the question of whether I have XHCI or regular 4". Does anyone know the OD of these standards?
  5. Baltik

    Offset toilet flange for 4” cast iron pipe?

    Hi Sylvan - are you referring to removing the old flange? or the actual CI elbow? I do not have access to the piping aside from the top so replacement options are limited. Is there an offset caulked CI floor flange?
  6. Baltik

    Offset toilet flange for 4” cast iron pipe?

    Appreciate the advice, the pipe i have appears to be lead and is part of original construction from 1967 it's 4"ID 5"OD and start to curve almost immediately. I have some flexibility in terms of height but can't do a full 2" rise. That means that the adapter should be an inside fit adapter that...
  7. Baltik

    Offset toilet flange for 4” cast iron pipe?

    Right - my pipe is slightly above the floor level, it’s also an elbow so I don’t think I can cut it much, photos for clarity
  8. Baltik

    Offset toilet flange for 4” cast iron pipe?

    Correct me if I’m wrong but all of these adapters have 4” openings, my ID is 4” so I don’t believe these will fit. I need something that is an inside fit
  9. Baltik

    Offset toilet flange for 4” cast iron pipe?

    I’m in the middle of a bathroom remodel and am facing a small dilemma. The existing 4” ID cast iron connector has a busted flange and is 11” from the wall vs the 12” I need for my Woodbridge toilet. I’ve found a few offset adapters but they would raise the toilet about 2” higher which wouldn’t...
  10. Baltik

    Silicone and gasket for Leaky tub drain?

    thanks Terry! here is the tub https://www.wyndhamcollection.com/showers-tubs/ursula-59-soaking-bathtub-by-wyndham-collection-white__wc-btk1511-59.aspx
  11. Baltik

    Silicone and gasket for Leaky tub drain?

    So my recently installed (not by me) tub is starting to leak at the drain. I wanted to take the opportunity to replace the drain at this juncture anyway. The new drain comes with 2 rubber gaskets (and no instructions) should I just use the gaskets or is advisable to use putty/silicone as well?
  12. Baltik

    Looking for obscure adapter

    i need a super low profile P-trap (every inch lowers the ceiling of the family room). I bought this one and am trying to connect it to a bathtub drain: https://www.amazon.com/gp/product/B00VV4PLF8/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
  13. Baltik

    Looking for obscure adapter

    I’m not thinking straight, lol. Is stainless ok in a dwv application or will it eventually rust through?
  14. Baltik

    Looking for obscure adapter

    That looks promising but I think wrong material - won’t glue with abs/pvc
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks