Search results

No, but I will and thank you for reply and effort. It appear that they are dedicated to the customers, will see their response.

Hi, its been 5 years since bathroom renovation and recently my wife told me that sometime out of nowhere water in the shower start dripping. Not sure if she is right, it is probably just some leftovers from the pipes and shower head, but, then I realised that if there is a real dripping problem...

Hi, is there some professional who can recognise this product? I guess this is just some rebranded product and because there is no much manuals and support for particular model, that behind the scene is some well known brand of softener. Here are some photos of the product in use and board for...

Hi and thank you! Here is a pressure, in average 3,5, but can drop to the 2,8 all the way to the 4. Bathroom is renovated 2 years ago and all taps are new, and very high quality. Ok, maybe some are not good (sink have 2 on the same line) but I am not sure that 2 taps became bad at the same time...

This happen before, a year ago. Water in my bath tub just stopped running, like someone cut the cold line. I found googling that it is maybe airlock problem and what I need to do to "unlock" it. Advise was to open both cold and hot water in the bath tub and with the hand palm press tap to...

Got it! Ill get back with the results as soon as circle of regeneration is closed. Thank you!!!

Does this help? Or to check somehow directly on device?

Just checked with the lamp height of the resin in the tank. It is 63cm from the floor to the top of the resin, which is approximately 25 inch. Calculation say that it is 1,5 ft3. Hmm. Do I need to change some settings accordingly?

Thank you for pointing that up. I have talked with the seller recently about eventual replacement of the resin and he confirmed that there is no gravel in the tank, only resin. He also told me that there is 2ft3 of the resin and in case of replacement I would need 2ft3 of it.

4. Thank you very much for clarifying this to me. There is no doubt about resin volume, it is 2cuft, I have checked with the guy who sold me the device price for eventual resin replacement and there is for sure 2cuft of resin. Also, found sticker on the tank and it is for sure 12x48 inch...

1,2. Well, not sure if we done it correctly then. Its filled with water and regenerated within few hours and now is in production. :confused: 6. Yes it is in grains (gpg), I kept settings like that for easier following you guys and left it like there until today. Hardness is measured with...

Hi everyone again, I need to please anyone willing to give me advise regarding one potential issue. I have already asked for advise here and get professional help and advises few years ago regarding adjusting my Fleck 5600SXT device which worked flawlessly until recently, when authorities...

Got you all guys, Ill try flush it with angle stop removed as soon as I get some free time. Meanwhile, got cold water back on a bathtub too. I hope you are right about this, because, if I am right, that is much bigger problem then debris or angle stop issues. Thank you for all advices and ideas...

Thank you all for tips, just to clarify few things. Bathroom and installations are new, just 2 months since we start using it and there was no any other problems with it then this. Sink have stop valves, flat washer type, but bathtub does not. There is a flexi pipe connected directly to the 18mm...

Thank you Terry for tips, but I am not sure that it is a case because there is 0 flow there. If there is some kind of dirt, it would at least have some drops of water, but that is not the case. There is literally no a single drop of water. Plus, unlike last time, now I had exactly same problem...

Have finished my self my bathroom on the upper floor of my house approximately two months ago. Have used pipe in pipe system, Wirbo/Uponor q&e connection. Everything worked just fine until about a 2-3 weeks ago when suddenly stopped run cold water from the bathtub faucet. Have tried to Google...

Hmm, when I asked you for advice some weeks ago, you told me to check which valve is in question there, and I dint know that I can read it on the case of the head and I disassembled it. There was only white plastic thing, dont know if that is what you meant by white, blue or red? Is it possible...

Got it. Now I understand that :) This is what I have there. Regarding brine fill, to be honest, I was not all the time beside device during this 60 minutes, so it is possible that all brine is sucked out in 15-20 minutes. Next time I'll follow it thoroughly to confirm. Thank you very much...

Dear sir, I have readjusted settings by your instructions and it appear that everything is in order now. Have tested TDS again and it is like 430 now, guess it is ok. There is no salty taste anymore. During BD, I think that all brine was sucked out after maybe 30-40 minutes. Is that normal...

Yes it is :)