Search results

Thanks Terry. I've been using the Korky valves but I don't know what's happened as the last one I bought sets too high (at or just above the lid height) and is causing problems. Also, the top part sets almost against the side of the tank. All of this, at times, causes the water to keep flowing...

Hello folks, I'm very grateful for all of you who get us DIYers out of jams. An eon ago I bought a very small one piece Toto toilet for my very small bathroom. It's served me well generally speaking. I've replaced several fill valves over the years but due to apparent water loss when...

Thanks Mr. Tuttle. I thought I had set up automatic notifications for my post but apparently not. I apologize for my delayed response. As I just mentioned to Terry, the 'gripper' on the basin wrench just takes up too much space and I've looked but I haven't been able to find a socket wrench of...

Thanks Terry. I apologize for being so late in commenting but I thought I had notifications set up for this post but apparently I didn't. The basin wrench 'gripper' is too wide and the socket is the best idea I've seen. But, the nut is about 1.25 or 1.38 AF and I've looked and looked but I...

My best wishes to all. I need to replace the faucet on a bathroom vanity as the water flow is unacceptably slow. I've looked at other reasons for the slowness of the flow, but it comes down to the basic design of the faucet - which came with the vanity. I've bought a replacement faucet. I'm...

My best to all. I have an almost 40 year old townhouse and I installed a programmable thermostat in it about 30 years ago. No problems with the thermostat until very recently. It has developed some issue that prevents me from changing the program and for awhile now (weeks) it runs the A/C for...

Good day to all. Situation: My small upstairs full bath was remodeled about two years ago (two-level townhouse). The vanity and the faucet were replaced but I believe that the faucet came packaged with the vanity and the top. I've been getting complaints from my stepdaughter about the low...

Thank you Mr. Marlinmen. You've put me at ease as I have ordered the 133504 part and it should be here by Wednesday. I assume you've compared the two photos - my original photo and the 133504 photo - and have concluded that the 133504 part seems to be the one that will work in my application. I...

My primary problem is my ignorance. I'm not familiar at all with recent shower faucets and cartridges. What I thought would be a 'stop' apparently isn't. Setting that aside, My concern is that the part 133504 doesn't look like the photo I uploaded of the broken off cartridge. Ref - my initial...

Mr. Marlinman: A question - the photo of the part differs from the photo I posted. Is this possibly because the part photo from premier includes the "stop" - which I'm completely ignorant of? My son in law didn't mention anything about having or seeing another part. Can I assume that the...

WOW Mr. Marlinman - I can't thank you enough. A tip is in order. May you be blessed for helping others.

Thanks Mr. themp. I really appreciate your time and effort. Let's see what happens when the old one is removed. Thanks again.

Thank you very much. My fingers are crossed - difficult to type this way though.

Thank you Mr. Tuttles. That was very helpful. Regards, snorp

My regards to all. Son in law is renting a TH and somehow!!! someone broke off the water supply handle for the shower. He's unable to work and I'm retired with only SS income = necessity to be frugal. Please refer to the attached photos. I'm not familiar with this type of setup. The 'name' on...

Thank you Mr. Tuttle. When I posted this thread I was sure that both stops were turned on - I had just been tightening up the connections. I Was Wrong. The water is flowing just fine now. Currently, when the handle is in the clockwise - left - position, it is in line with the 'water flow'...

Hello to all and my thanks for what you do. I'm installing the subject faucet and have ran into something I don't know how to 'fix'. Instructions say to insert the shank with the notch facing forward. Low light level and cramped space made this problematic - did the best I could. Checked the...

Yes Jadnashua, I was able to reach into the 'grinder bowl' but I couldn't feel or see anything other than the 'grinder blades'. So - I called the company for help. After being told that it wasn't likely or possible for the plug to be anywhere else but in the 'grinder bowl' I tried again and...