Search results

Jeff, thanks for the reply. I actually have a metal DryerBox at the bottom for the exact reason you describe. To have additional room for the vent pipe and the gas flex line to nest a bit and allow the dryer to be pushed back further. Also, I am 100% with you. I did consider serviceability...

Typically, any time I've set up a gas dryer the valve is always behind the unit near floor level. Of course access requires pulling the dryer forward. I am roughing in a laundry room and the gas line is actually coming from the ceiling and down inside a framed, outside wall. I was thinking...

Wayne, Once again (for probably the 15th time over the last year plus), thank you. You are correct in all of your assumptions. Actually, your idea of Alt 1B may be the best bet simply because I have all the fittings necessary to do that vs. having to order the 3x3x3x2 San-Tee with Right Side...

Had to go out of state for a month for some family stuff. Finally back to working on the house. Decided on a possible change to the layout. The following pic has two alternatives and is a plan view of the layouts. I think both would work to wet vent the entire bathroom group. (Note that...

Wayne, As always you are supremely helpful. I don't know what I was thinking about wye for the shower. I was being dumb there. As it turns out, I have a decent amount of flexibility with this layout. This is all coming down from the second story, the stack will be behind a wall and the W/C...

On to the next bathroom that needs to be completed. This should be pretty straightforward. Is this layout acceptable (see attached pic)? A few questions: 1) Is the single 2" vertical stack vent appropriate for the water closet and the shower? 2) Is the best choice a 3" double wye (with...

Hello. I am a WAYS away from actually getting to the tile stage. For now, my plan is to fur out the wall and install some kind of edge profile. I might still consider moving the toilet flange so I can then fur the entire wall out he same distance, but I am not at the point I have to make that...

Thanks for the fast response guys. I'll proceed as planned and center the valve.

On to the next item of the remodel saga. I'm completing the layout for the master bedroom/closet/bathroom. As you'll see from the rough print I created, If I center the shower valve, it would result in it being at the dead center of the intersecting wall between the bathroom and walk-in...

Thank you everyone for the continued ideas. One key item that may or may not matter. I roughed in all new water lines and have NOT filled them yet. So Ideally (if possible) I'd like to complete a thorough cleaning/flush of the rank without running water to the new lines yet. So if I can put...

Thank you everyone for the feedback. Quick update. I put some water in the tank for the first time in a long time, and then drained some of it (I did get a small amount of sediment/rust particles). Filled it some more again and drained some more and it was clearer. I have it filled right now...

When it was filled, it was filled with chlorinated city water. I have a nearby sump pit that I can drain to. I think I'll move forward with the plan to fill it up and drain it out and see how that goes. My main concern would be if any bacteria or mold could have started to form inside the...

As I get closer to pressurizing the entire system for the first time, the next item to address is the water heater. Quick story is that it was filled with water that sat for about a year (late 2019 to late 2020). About 16 months ago I emptied the tank fully and while the water that came out...

- I set the pre-charge exactly as you described. (set to 60 psi which is what my PRV is set to). Glad I did it right. Good idea on the empty tank sound. I'll do that.

Reach4, Just to clarify, this expansion tank is only on my incoming city water line (not my separate well water system). So there is no softener that I need to worry about. The city water is what will be heated. Also, My plan was to put a shut-off in the white pex line after the tee and...

Thank you all. What I started to debate was how important it is to have the tank closer to the "source" in terms of functionality. I guess I'm in one of those situations where I probably chose a location that will work in terms of the rules, but perhaps is not ideal compared to standard...

I'm installing a brand new expansion tank on my fully re-piped system. My current plan is to install the tank right after the incoming city water service. Although I started to rethink this for a few reasons. As you'll see in the pictures, everything else is basically completed (PRV, Water...

That is a reasonable solution and the tile will be going to the ceiling. I actually have a window that is right above the WC and near the tub. I can terminate the tile in the manner you described right before the side of the window trim and line it up perfectly symmetrical with the opposite...

Hey Wayne. Reasonable question. Unfortunately, the tub is already set in to a mortar bed and the drain is plumbed and glued (previous contractor). Of course I could dismantle all of that, remove the mortar and re-do it, but that does feel like perhaps a bit much to resolve this. The tub does...

Terry, Thank you. I'm sure you've set about 10000X more different toilets than I have. So that answers that question. Looks like I'm either not furring that side out much, or I'm resetting the closet flange (which really is not worth it). Shoot.