advice on hot water recirc pumps

Barrybpdx

Barrybpdx

New Member
Messages
41
Reaction score
0
Points
0
Location
portland, or
looking for advice on a hot water recirc system.
i'm replumbing and can add a recirc line back to the tank rather than sending the un-hot water into the cold line.
here's what i'm thinking:
- run a hot 'trunk' line that serves the 2nd and 3rd floor bathrooms.
- install a pump at the far end of the trunk line.
i want one pump with a temperature sensor, preferably adjustable, that shuts it off when hot water reaches the pump.
i'd also like to be able to push a hard-wired button in either bathroom to trigger the pump. on-demand only; no timer necessary and i sure don't want to keep the line hot all the time.

which is the pump for me?

thanks!
 
pump

Any pump will work, the electric controls are what you have to be concerned about. The pump can be anywhere in the system, usually at the water heater, as long as the outlet has a route back to the water heater
 
A Grundfos UP15-42B would work. It is available with integral checks, and a temperature sensor. The pump is usually located adjacent to the waterheater, but but that is not mandatory. You could simple have a switched outlet installed to plug the pump into. The Grundfos pumps are available also with line cord attached, which would make that switching option easy.
 
RedyTemp is an integrated system, has an adjustable temperature sensor and supports any of the power control functions. It seems a little more expensive than some others, but is really quick to install if you have an outlet where you need it. I've had one for about 3-years now and have it on a 7-day timer so it runs in the mornings and evenings.
 
RedyTemp is an integrated system, has an adjustable temperature sensor and supports any of the power control functions. It seems a little more expensive than some others, but is really quick to install if you have an outlet where you need it. I've had one for about 3-years now and have it on a 7-day timer so it runs in the mornings and evenings.
 
RedyTemp is an integrated system, has an adjustable temperature sensor and supports any of the power control functions. It seems a little more expensive than some others, but is really quick to install if you have an outlet where you need it. I've had one for about 3-years now and have it on a 7-day timer so it runs in the mornings and evenings. Taco
 
RedyTemp is an integrated system, has an adjustable temperature sensor and supports any of the power control functions. It seems a little more expensive than some others, but is really quick to install if you have an outlet where you need it. I've had one for about 3-years now and have it on a 7-day timer so it runs in the mornings and evenings. Taco also
 
RedyTemp is an integrated system, has an adjustable temperature sensor and supports any of the power control functions. It seems a little more expensive than some others, but is really quick to install if you have an outlet where you need it. I've had one for about 3-years now and have it on a 7-day timer so it runs in the mornings and evenings. Taco also makes one.
 
the ChiliPepper looks like another option, less expensive than the others. didn't have an option for additional hardwired switches.
i just called them and the voicemail says that there's a new model coming out today. hopefully they'll get the website updated soon and this new model will accept remote switches (instead of just wireless remote)
 
i was thinking it's best to locate the pump next to the farthest fixture. if i put it next to the HWH, then i'm heating (wastefully) the water in the return line, partly defeating the purpose of having the pump.

is there a compelling reason to put it at the HWH? noise? appearance?
 
You usually have power there, and while quiet, they do make some. Also, you may not want to take up room under say the vanity with the thing. I run mine so the water at the furthest location is just warm, not hot. For the shower, instead of taking over a minute to get hot, it takes maybe 10-seconds. The vanity on the first floor has hot water immediately, and the branch to the kitchen takes maybe 20-seconds. The systems like the Grundfos that use a valve at each (or at least has the option) fixture can reduce that at each fixture. When you just have one pump and no other fixtures, it depends on how your piping is layed out, as to how quickly you get hot water.
 
You must log in or register to reply here.

Similar threads

R
Hot water recirc question
Replies
2
Views
398
Jeff H Young
Jeff H Young
Benze
Recirculation pump or gravity recirc in 2025?
Replies
6
Views
1K
Jeff H Young
Jeff H Young
J
Motion Sensor Hot Water Recirc Options??
Replies
6
Views
543
jahmes143
J
A
Help with Hot Water/Recirculation System Plumbing Design - New Residential Construction
Replies
3
Views
3K
abc123puck
A
O
Thermosyphon system
Replies
16
Views
808
Reach4
Reach4
Back
Top