need advice on gas pressure test

lati_cz

lati_cz

Member
Messages
30
Reaction score
0
Points
6
Location
Sunnyvale, California
Hi guys,
I am adding a second bath. I had to relocate few gas pipes. I tried to test it today, I was able to pressure the system only at 2 psi. I found out, the air leaks from vent at gas meter (small round opening). Is the gas meter faulty? What should I do? How many psi should be system tested at? I'd really appreciate help, thanks Michal
 
Disconnect it where the gas meter is and cap the line and pressurize it to 15 pounds, and let it set for 2 hours at the minimum. Over night is the best test
 
Gas pressure test

Yes call a real licensed plumber before you and your house go ka boom

in the middle of the night !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
 
So you put 2 lbs pressure on the meter outlet? You NEED to call the gas company NOW. Whatever you do, do not turn the gas main back on.
 
You NEED to call the gas company NOW. Whatever you do, do not turn the gas main back on.
Click to expand...

When a plumber does a static pressure test, the pipe is disconnected from the meter.

This is a case of knowing too little.
NHmaster suggested calling the gas company, that may be a good idea at this point.

I've never heard of anyone trying to pressure test while connected to a meter before.

Sometimes an inspector will allow other methods of testing if you are going to keep the gas connected.
With new installs, they aren't even allowed to connect a gas meter until the pipe has been tested and inspected.
 
Last edited:
Just to elaborate on why the others are saying to call the gas company. You may have done serious damage to your meter and or your appliances. While the testing should be done at high pressure (15 PSI +) the regulators and appliances are designed to see 1/2 PSI. You have probably ruptured a diagram or jammed a piston in side your meter.

The "vent" you had bubbles out of is a reference to atmospheric pressure. It should NEVER have gas or air coming out of it. The meter is also a pressure reducing valve. If that is damaged appliances not build to take the very high pressure of the main pipe in the street could go boom.:eek:
 
meter

THe gas regulator is designed to vent ANY pressure above its setting, that is why it is there. So, your pressurizing the downstream side just simulated a regulator failure and it did what it was supposed to do. Disconnect the meter, cap the pipe, and do the test. The meter is fine and so is the regulator.
 
Gas test ! ! !

No no !!!!!!!!!!

You don't know what the pressure "might" have damaged follow the
other plumbers advice !!!!!

Call the gas co. Today ! ! !

More than likely you have ruptured the gas valves on all the appliances
that were connected at the time of your test !!!!!!
 
pressure

The vent is there to PREVENT damage to the meter and system from excessive pressures. You can call, but I have seen this many, many times and there has NEVER been a problem afterwards.
 
Thanks guys.
Lesson learned. Gas comp. came, tested it. The meter is good, the regulator had small leak, they changed it. The guy couldn’t tell if I caused it. The regulator holds up to 60 psi from outside, only 1,5 from inside.
He said it’s common, he said even some contractors pressurize the system without disconnecting the meter… All the appliances were turned off at the time of testing, no damage there. I wish I asked my friend plumber more questions before testing.
 
You must log in or register to reply here.

Similar threads

F
Gas line integrity based on?
Replies
3
Views
3K
Jeff H Young
Jeff H Young
C
Air pressure for Thermal Expansion Tank above Water Heater
Replies
12
Views
791
Jeff H Young
Jeff H Young
F
Generac Natural Gas Line
Replies
9
Views
9K
John Gayewski
John Gayewski
W
Pressure testing hydronic heating line
Replies
0
Views
1K
wworden
W
viper1
New gas service. Can we get meter turned on with capped/ pressure tested only?
Replies
8
Views
2K
John Gayewski
John Gayewski
Back
Top