What thins latex paint?

Users who are viewing this thread

Chassis

Engineer
Messages
340
Reaction score
0
Points
16
Location
SE Pennsylvania
Besides water. I have a door jamb to repaint, and don't want a thick buildup of paint, which will make the door hard to shut. I was reading that methy ethyl ketone (MEK) will dissolve in water. I know that water will thin latex paint. Can MEK thin latex paint also? Would like to find something that thins the paint, flashes off (dries) quickly and aids in paint flow.

For oil paint, I have used boiled linseed oil to thin the paint and improve flow. Wondering if there is something similar for latex paint. Thanks.
 

Prashster

New Member
Messages
936
Reaction score
4
Points
0
Why not water? Why does it have to flash off quickly?

Other things to try (in order of increasing strength): isopropyl alcohol, ethanol, methanol, acetone (similar to MEK).
 

Jadnashua

Retired Defense Industry Engineer xxx
Messages
32,770
Reaction score
1,190
Points
113
Location
New England
To get a satisfactory result, follow the instructions on the particular paint you are using! It will say on the can somewhere, and if it is an old can and covered up in paint drips, you can probably find out on the manufacturer's website or call them.
 

Verdeboy

In the Trades
Messages
2,041
Reaction score
6
Points
0
I don't understand how one coat of paint is going to cause your door to stick. If it's that tight already, I think you should sand down your door jamb, chisel out your hinge mortises a bit, or just plane the door a little. Don't forget, the next time it gets really humid in SE PA, all the wood will swell and the door will really begin to stick (if it's that tight now).
 
Last edited:

Chassis

Engineer
Messages
340
Reaction score
0
Points
16
Location
SE Pennsylvania
Good points made by all. I just want to do things better, and try to do it like the "pros". I like the boiled linseed oil trick I learned, so was hoping there was a better solution with latex. I thought maybe there was a space age way to do this, but I guess not.

Verdeboy, I hear you on the humidity thing. I experienced this alot recently, because I am redoing all the door hardware on my front entry. This includes door hinges for both storm (wood) and main doors, as well as lockset, and the other jewelry on the door. This past September has has several wet spells interspersed with very dry weather. I have taken the opportunity to ensure the doors swing freely under all conditions.

Going back to my initial question, I can certainly sand down a few layers of paint on the jamb, then repaint. But I was looking for the "right" way or "cool" way to do it. A-sanding I will go...... ;)
 

Jimbo

Plumber
Messages
8,918
Reaction score
18
Points
0
Location
San Diego, CA
You need a certain minimum film thickness for a proper paint job. Any paint is a little thick if brushed, thinner if sprayed. If you thin any paint too much, you will not get coverage. The label for any paint will give the maximum amount of thinning. But if one coat of paint will cause clearance problems, I would suggest the door is not installed correctly.
 

Cass

Plumber
Messages
5,947
Reaction score
7
Points
0
Location
Ohio
If you try the Floetrol you'll like it. Gives a really smooth finish so long as the prep is smooth.
 

hj

Master Plumber
Messages
33,602
Reaction score
1,038
Points
113
Location
Cave Creek, Arizona
Website
www.terrylove.com
paint

One of my son's friends worked for a professional painter. They thinned the paint with water to the point that you could still see through the paint when it dried. The more you thin the paint the less pigment that gets applied. It makes a thinner layer, but also defeats the purpose of putting paint on in the first place.
 

Cass

Plumber
Messages
5,947
Reaction score
7
Points
0
Location
Ohio
hj said:
One of my son's friends worked for a professional painter. They thinned the paint with water to the point that you could still see through the paint when it dried. The more you thin the paint the less pigment that gets applied. It makes a thinner layer, but also defeats the purpose of putting paint on in the first place.

Yes but you are reducing the % of the part that holds it to the surface to the point that it won't adhere right. That is why there is a max amount of water allowed for thinning.
 
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks