(206) 949-5683, Top Rated Plumber, Seattle
Page 2 of 2 FirstFirst 12
Results 16 to 19 of 19

Thread: Front Load Washer

  1. #16


    Quote Originally Posted by Mikey
    You might also look at very heavy-duty slide assemblies to facilitate service, so that when cols' husband shows up he can just unlock something and slide the units out for service.
    LOL !
    I asked him this question, but I misunderstood, too. I thought you just wanted to mount the AW on a "pedistal". My DH laughed when I told him that the salesman said it had to be a "special" one.
    DH says that the pedistal will have to be able to slide out with the machine for service. You cannot expect a tech to pull the appliances down off of your "cabinet". Your plan sounds good for your backs...not so much for the tech. Like I say, rest assured that, no matter what brand you buy, YOU WILL NEED SERVICE some day.

  2. #17
    Homeowner geniescience's Avatar
    Join Date
    Nov 2005
    humid summers hot, humid winters cold

    Default easy to do; idea is good.

    I love my front loading washing machine. It performs way better than any top loading machine. Just don't try washing a single little heavy thing -- the machine will never even begin to spin dry! It spins close to 2000 rpm once it settles the load out, balancing weights. Everything comes out practically dry enough to wear five minutes later.

    I too am going to build a counter top height shelf, or platform. It'll have long term storage space underneath and lightweight storage beside the washing machine. It's true there is a risk of a spinning washing machine creating a dynamic load that is higher than any load that a "regular" piece of furniture is designed around, and that would cause regular furniture to come apart over months and years. To me, that is not a problem, not a complaint, and not a challenge. I figure I can build a structure that will handle far more than just the weight of the machine, so all dynamic load vibrations are absorbed without putting the bolts and joints at risk.

    I am planning to use the ceiling and the walls to bolt my structure in place. I will use the floor too; it won't be all hanging from the ceiling. But still, I think it is important to mention that the strongest structure will go floor-to-ceiling and will be fastened in many places to the building (walls and ceiling) so that you are not just hoping it holds together as a cube, or box, merely by standing on the floor. I figure steel angles and high grade plywood will be the best materials.

    To get around the need for access behind the machine, the platform will be wide enough to turn the machine around on it. No taking it down, don't want to risk unnecessary lifting. Beside the machine, on this wide platform, I'll probably have some lightweight shelves. If you put your dryer there it will still work as intended, with a little more effort. A dryer is an empty cube that someone with a strong back can slide out and carry away.

    A front loading washing machine vibrates very little. Hard to believe, until you have bought one and used it. It really is a big improvement over front loading machines. A real difference from the old. Less noise, less vibration.

    Whether vibrations go into the floor or the ceiling is not a concern. My opinion -- please comment if I have overlooked something here.

    Mike, that is my plan. Hope this helps you.

  3. #18
    DIY Member maddfrog's Avatar
    Join Date
    May 2006

    Default food for thought

    Most of the front loaders with front-mounted controls are 'stackable'. I would think if you can stack them, you can certainly put them on a counter top of whatever height you'd like, as long as it's strong enough to support the weight and handle some vibration.

    I recently replaced a top-loader that used to occasionally walk itself in front of the laundry room door, making it difficult to get into the room to push it back. Since installing the new Frigidaire washer, it hasn't moved so much as 1/16". I was surprised by how little it vibrates even at full spin RPMs.

    In terms of service, the washer has a service panel on the front that gives access to most of the internals. Wouldn't think you'd need to take it down very often. Dryers don't weigh much and should be easily taken down.

  4. #19


    Quote Originally Posted by maddfrog

    In terms of service, the washer has a service panel on the front that gives access to most of the internals. Wouldn't think you'd need to take it down very often. Dryers don't weigh much and should be easily taken down.
    Most brands (Maytag/ Fridgidaire/Samsung, etc) require the tech to remove the TOP in order to get the front panel off.
    "Dryers are light weight".....well, that's as may be, but most techs will not take the dryers down by themselves SO you will be at the very least paying for two guys to show up and at worst having a great deal of difficulty getting service at all.
    I'll say it again, YOU WILL REQUIRE SERVICE !


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts