(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 5 of 5

Thread: Spigot to ice chest

  1. #1
    DIY Junior Member Flyinpig14's Avatar
    Join Date
    Aug 2013
    Location
    Louisiana
    Posts
    1

    Default Spigot to ice chest

    Hello everyone,
    I'm not sure if this is the right place to ask this or not, but I thought maybe someone here could help me. I am building a wooden ice chest box around an ice chest. The ice chest doesn't have a drain plug, and I am trying to figure out how to add a spigot to the side. I already ruined one ice chest by drilling a hole and apparently using all the wrong parts to try and add this spigot. It doesn't need to be anything fancy, just any suggestions would be greatly appreciated. I am a complete idiot when it comes to this stuff so please take it easy on me!
    Thanks in advance!

  2. #2
    DIY Senior Member dj2's Avatar
    Join Date
    Aug 2013
    Location
    California
    Posts
    315

    Default

    Don't you think it would be easier to buy an ice chest with a built in spigot?

    But just in case you can't do that, a spigot most likely comes with a rubber washer, a metal washer and a nut, that go inside the chest to plug the hole and to stop leaks.

  3. #3
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,405

    Default

    It really depends on what the chest is made out of. A picture might help.

    If it's something that is soft, like a plastic, you may need to bond it in place rather than try something to make a compression seal (i.e., with a nut and washer). There are some good waterproofing compounds out there - one that comes to mind is KerdiFix, which will stick to nearly anything, is flexible, and waterproof. It's kind of expensive, but comes in, I think, three different sized tubes - the smallest would be way more than enough.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  4. #4
    DIY Senior Member Smooky's Avatar
    Join Date
    Apr 2011
    Location
    NC
    Posts
    486

    Default

    Google: draft beer faucet and shank

    and see if that will work
    Last edited by Smooky; 08-15-2013 at 07:57 PM.

  5. #5
    DIY Junior Member mrbeing123's Avatar
    Join Date
    Dec 2012
    Location
    Louisiana USA
    Posts
    19

    Default

    I can try to help. We uses these a lot for drums, hoppers and tanks where I work (oil/gas chemical blending company). Might want to check the miniature ones but I see there are no gaskets on it. With these, you would then have a female threaded fitting, where you could add whatever plumbing too it that you want. But like jadnashua said, the ice chest's insulation might compress too much to use something like this. Again like he said, bonding it with a proper adhesive might be in order. If I had to say what kind of adhesive, I would go with maybe an acrylic based epoxies specifically made for plastics.
    http://www.mcmaster.com/#tank-pipe-fittings/=o3bvye
    Last edited by mrbeing123; 08-16-2013 at 11:44 AM.

Similar Threads

  1. ABS wye with spigot end
    By Seattle38 in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 3
    Last Post: 05-21-2013, 06:52 AM
  2. Tub spigot
    By BellPilot in forum Shower & bathtub Forum & Blog
    Replies: 4
    Last Post: 11-08-2010, 03:53 PM
  3. Spigot PSI pressure
    By Cygarbuff in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 8
    Last Post: 08-08-2009, 02:55 PM
  4. Spigot Supply Valve - Pipe to outside spigot
    By drjimmy in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 18
    Last Post: 01-26-2009, 05:03 PM
  5. Outside Spigot Repair
    By mlordi in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 6
    Last Post: 04-26-2008, 03:52 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •