(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 10 of 10

Thread: 3 handle tub/shower rebuild

Hybrid View

  1. #1
    DIY Junior Member dsgt's Avatar
    Join Date
    Jul 2013
    Location
    California
    Posts
    7

    Question 3 handle tub/shower rebuild

    I just had a three handle tub/shower rebuilt using Price Pfister rebuild kit and the outcome is aesthetically unfortunate. The hub of the faucet handle is about an inch shorter than the sleeve and 1/2 inch larger in diameter. Apparently there are no parts that will allow the hub to fit flush against the tiled wall. It is functional and has an excellent seal, but the appearance would be greatly improved if the sleeve and the hub were the same diameter. Any suggestions for solving this problem will be hugely appreciated.

  2. #2
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,383

    Default

    Rebuild on old shower controls that (probably) don't have today's minimum requirements is, IMHO, kind of a waste of time and money. Yes, you can legally, per code, rebuild an existing installation in most places, but it's better in the long term to replace the whole shebang. It is rare that someone makes trim that fits older faucets. Not saying it doesn't happen, especially if it was a particularly popular one, but there isn't a huge market, and the variations makes it uneconomical. The remodel plates generally required to cover those holes when a new one is installed don't look bad (would look better than the gaps you have!) and would work until you decided on a remodel and can do it without one.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  3. #3
    DIY Junior Member dsgt's Avatar
    Join Date
    Jul 2013
    Location
    California
    Posts
    7

    Default

    Thank you. Decision to rebuild is based on (a) need to shower and (b) not ready to rip out and replace the wall/floor tile yet. Can you tell me more about the remodel plates are you suggesting?

  4. #4
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,383

    Default

    To get access to the existing valve (unless you can get to it from behind), and remove it, you need a bigger hole. THen, you need to cover it or rebuild the wall. Often, you do not want to rebuild the wall. Each company seems to make one or more in various finishes and shapes to cover that bigger hole. Then, you mount the new valve's trim on top of this. I used one like this at my mother's house awhile ago to replace her aging tub/shower valve. http://www.deltafaucet.com/repairpar...rp29827ss.html This Olde House has a segment where they installed one, you can probably find and watch it on their website.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  5. #5
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,615

    Default

    I would have to see what parts you used, and what the old ones looked like. If you used the correct parts, it would look EXACTLY like the old one, although if I had repaired it, it would look like the current models, but in any case the handles and flanges would fit correctly. I would also have to know what you mean by "sleeve" and "hub" because those terms have a specific connotation.
    Licensed residential and commercial plumber

  6. #6
    DIY Junior Member dsgt's Avatar
    Join Date
    Jul 2013
    Location
    California
    Posts
    7

    Default

    Thanks to both of you. I could not begin to explain the terms hub and sleeve. I looked a labeled diagram to learn how to describe the problem to people who actually understand plumbing. Someone who looked at a picture of my shower said all the stuff inside the wall needs to be moved further back. I don't know if that is possible, but it's worth pursuing.

Similar Threads

  1. going from two handle shower body to one handle-- using converter plate
    By dayexday in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 5
    Last Post: 09-24-2012, 06:47 AM
  2. Shower handle and trim for 22 year old pull-out handle
    By Steveindanville in forum Shower & bathtub Forum & Blog
    Replies: 9
    Last Post: 12-23-2009, 10:27 AM
  3. Converting 3 handle to 1 handle in shower/tub
    By dixielou in forum Shower & bathtub Forum & Blog
    Replies: 3
    Last Post: 03-19-2007, 06:59 AM
  4. single-handle Aqualine shower handle
    By marchat in forum Shower & bathtub Forum & Blog
    Replies: 1
    Last Post: 12-29-2006, 02:18 PM
  5. Please help with my shower rebuild
    By gene250 in forum Shower & bathtub Forum & Blog
    Replies: 14
    Last Post: 07-09-2005, 01:25 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •