(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 4 of 4

Thread: Help: Shower faucet and valve

  1. #1
    DIY Junior Member stautxie's Avatar
    Join Date
    Jul 2013
    Location
    Orange County, CA
    Posts
    1

    Default Help: Shower faucet and valve

    Dear all,

    I am stuck while remodeling my bathroom and want to seek your advice.

    1. I want to change shower valve handle and try to avoid soldering. I have already removed the original handle and plate but stuck at the cap. I think I can screw in a replacement handle, e.g. Pfister's universal handle, if I can get rid of the original cap. I cannot unscrew it with a plumber's wrench. Any suggestions?

    Name:  photo.jpg
Views: 147
Size:  51.1 KB

    2. I am trying to replace the shower head as well. After stripping the old head, I am stuck with the spherical end that does not come off at all. Any thoughts on it?

    Name:  photo (1).jpg
Views: 104
Size:  44.8 KB

    Thank you all for your attention.

  2. #2
    DIY Senior Member asktom's Avatar
    Join Date
    Nov 2009
    Location
    Victor, MT
    Posts
    464

    Default

    The rule of thumb is that if you open the wall you change the valve. There is no such thing as a universal handle, yours looks like it takes a Delta. Try any handle you get before you close the wall. You will need to use a new shower arm if you are changing the head.

  3. #3
    Forum Admin, Expert Plumber Terry's Avatar
    Join Date
    Aug 2004
    Location
    Bothell, Washington
    Posts
    14,221
    Blog Entries
    1

    Default

    It would be regrettable if the valve isn't replaced at this time.
    New ones are pressure balanced, and it's getting harder and harder to find parts for the old stuff.

    You will need a new shower arm without the round knob end. It should have 1/2" pipe threads on both ends.

  4. #4
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,687

    Default

    You have a Delta valve, and since it is the very first 'generation' there is NOT handle except the lever one with a ball on the end which will work with it. To replace the shower head you have to also replace the shower arm. There should be three small tubes joining the front and back parts of the valve, and if you are not careful you will twist them off and then you will HAVE to replace the faucet.
    Licensed residential and commercial plumber

Similar Threads

  1. Shower Faucet Valve
    By sec1jrs in forum Shower & bathtub Forum & Blog
    Replies: 4
    Last Post: 07-27-2011, 04:11 PM
  2. What type of shower faucet valve is this?
    By JMichael in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 1
    Last Post: 01-30-2011, 06:55 AM
  3. Shower-only valve/faucet/trim
    By Optiker in forum Shower & bathtub Forum & Blog
    Replies: 10
    Last Post: 12-13-2010, 05:56 PM
  4. Shower Faucet Control Valve positioning
    By raanders in forum Shower & bathtub Forum & Blog
    Replies: 4
    Last Post: 09-27-2008, 08:02 AM
  5. safety valve- shower faucet
    By hlsess in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 4
    Last Post: 01-17-2008, 06:39 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •