(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 2 of 2

Thread: NatGas valve water exposure - effects?

  1. #1
    DIY Junior Member KTMBerg's Avatar
    Join Date
    Jan 2013
    Location
    ALB, NY
    Posts
    1

    Default NatGas valve water exposure - effects?

    If a little water backs up into a gas valve, is it likely hosed?

    My Rinnai R94LSi suffered a minor flood of water flowing through it for a short period of time when our sewer stopped up and water backed up through the ventstack condensate drain! (A check valve in addition to the gas trap would have been a good suggestion in the installation manual.)

    It immediately threw a code 11 (no ignition) the next time the unit attempted to run.

    When tearing it down to dry it out, I found the gas manifold full of H2O and some sitting in the outlet ports of the now-exposed dual port gas valve. I can presume some water crept into the valve(s) when the unit called for gas.

    Thoroughly cleaned and dried everything (except the non-serviceable gas valve), reassembled, and all is good... so it seemed. Then it starts thowing a code 12 (flame failure) from time to time particularly when the gas flow is on its lowest setting to match low flow through the unit. Inspecting the flame in that condition, it's there but barely. Flame is just dandy on higher-demand settings. Flame sensor wires were checked and cleaned, with no change in results.

    I can't find parts for Rinnai online so I guess I need to grovel to a dealer? Surely they hate DIYers.

    Any feedback would be greatly appreciated!
    Last edited by KTMBerg; 01-09-2013 at 09:09 PM.

  2. #2
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,412

    Default

    Most gas valves should not be reused if they get immersed, and should be replaced. Most places don't like to sell gas parts direct to consumers for liability reasons, so your experience isn't particularly unusual. Whether it is actually safe, I cannot say. The owner's manual will probably have a statement about this situation, if not, call them to verify.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

Similar Threads

  1. Installing PEX, what constitutes UV exposure which requires protection?
    By DaveHo in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 3
    Last Post: 05-10-2012, 06:40 AM
  2. Cant take the effects of hard water in N. Phoenix, need help quick!
    By Tonyc@alpine in forum Water Softener Forum, problems, installation and reviews
    Replies: 11
    Last Post: 02-21-2012, 04:14 PM
  3. Effects of freezing on traps and toilet?
    By krosspen in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 12-08-2010, 05:10 AM
  4. PEX and UV exposure
    By JGLA in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 3
    Last Post: 06-26-2010, 05:54 PM
  5. ABS sunlight exposure
    By AverageMe in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 4
    Last Post: 10-27-2009, 06:52 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •