Pressure problem on jet pump

Users who are viewing this thread

JoshB-NC

Member
Messages
37
Reaction score
0
Points
6
Location
North Carolina
Just getting finished installing water softener and iron filter. Was going to raise the pressure of the pump up to 60/40. Its a 50/30 now. Pressure in house after going through filters is not quite what it was.

Anyways - pumps kicks on at 30psi runs until about 52psi and kicks off. Pressure immediately drops to 45psi and stays there. It was doing this before any filters were added. Pressure gauge is on top of pump and the line for the switch is off the front of pump. Am I getting a false reading since its mounted on the pump? It will hold the 45psi until you run the water and kicks back on at exactly 30psi every time.

Its a goulds JRD10 jet pump, bladder tank (set at 28psi). Its mounted to the well casing.

Any ideas?
 

LLigetfa

DIYer, not in the trades
Messages
7,497
Reaction score
575
Points
113
Location
NW Ontario, Canada
Yes. The only time it should be on the pump is when the pump is right next to the tank. How far away is the tank?
 

JoshB-NC

Member
Messages
37
Reaction score
0
Points
6
Location
North Carolina
The main line goes about 1.5' then the air tank is tee'd in. But the air tank has about 2' of 1" line before it tee's into the main line.
 

Texas Wellman

In the Trades
Messages
1,035
Reaction score
59
Points
48
Location
SE Texas-Coastal
The gauge reads jet pressure while the pump is running. Jet pressure is basically the backpressure on the pump. Do you have a regulator on the pump discharge? I'm not totally familiar with that model but I'm thinking you're simply reading the backpressure/jet pressure, which has to be a bit higher than the tank pressure to work right.
 

JoshB-NC

Member
Messages
37
Reaction score
0
Points
6
Location
North Carolina
The gauge reads jet pressure while the pump is running. Jet pressure is basically the backpressure on the pump. Do you have a regulator on the pump discharge? I'm not totally familiar with that model but I'm thinking you're simply reading the backpressure/jet pressure, which has to be a bit higher than the tank pressure to work right.

Yes it looks like there is something on the pump discharge. I wonder why the previous plumber put the gauge and the switch on the discharge? It was short cycling - coming on at 30 psi and shutting off at 52, but in reality it was 45. Pump is in good condition - I manually held contacts open and it will easily build 65+psi.
 

bcpumpguy

New Member
Messages
70
Reaction score
0
Points
0
Location
Langley BC
those distances from tank should not be an issue on a jet pump, probably have failing foot valve. Dont change the switch unless it worn out, just adjust it by tightening the larger rod nut and spring by tightening the nut on top. or if you want to get a new switch just get one i suppose. Low pressure cut off or LLC shuts off the pump if the pressure goes below 30 psi so that it does not burn out the pump. pressure going this low would either be loss of prime (low well level or suction leak) or water used beyond the capability of the pump. the can be a pain in an area where there is many power outages as you would have to reset the switch whenever pressure goes low. If you dont run out of water now its not worth it.
 
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks