(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 15 of 19

Thread: New water well

Hybrid View

  1. #1
    DIY Junior Member dENNIS MEYER's Avatar
    Join Date
    Oct 2012
    Location
    TEXAS
    Posts
    6

    Default New water well

    I'm planing on having a 4'' well driled it should be about 250' deep. I would like to save myself some money by installing the submersible pump myself. There will be two people one strong & one week . If I install using threaded pvc pipe do you think the two people could do it ? Is there a clamp that I could buy that would hold the pvc pipe in place to keek the pump from falling in the well, to add another length of pipe ?

    If you have suggestions on what else I could do,I'm all ears.

    Thanks for any help you can give me

    Dennis

  2. #2
    DIYer, not in the trades LLigetfa's Avatar
    Join Date
    Feb 2011
    Location
    NW Ontario, Canada
    Posts
    3,687

    Default

    They do make and sell clamps specifically for the job but I just use a wood block clamp.



    If you want to go big...
    http://www.americawestdrillingsupply...PipeClamps.asp

  3. #3
    DIY Junior Member dENNIS MEYER's Avatar
    Join Date
    Oct 2012
    Location
    TEXAS
    Posts
    6

    Default

    Quote Originally Posted by LLigetfa View Post
    They do make and sell clamps specifically for the job but I just use a wood block clamp.



    If you want to go big...
    http://www.americawestdrillingsupply...PipeClamps.asp
    Thanks for the clamp info. I have been trying to find out some information on the pvc pipe not having much luck. I would like to know is it male on one end & femail on the other or are they both male ? I would also like know what the weight per 10, length would be ?

    Thanks

  4. #4
    DIYer, not in the trades LLigetfa's Avatar
    Join Date
    Feb 2011
    Location
    NW Ontario, Canada
    Posts
    3,687

    Default

    Quote Originally Posted by dENNIS MEYER View Post
    I would like to know is it male on one end & femail on the other or are they both male ?
    I would never trust threaded PVC female ends so would use M/M with SS couplers.

  5. #5
    Test, Don't Guess! cacher_chick's Avatar
    Join Date
    Jan 2008
    Location
    Land of Cheese
    Posts
    3,155

    Default

    I too would avoid PVC couplings. 1-1/4" schedule 80 drop pipe is about 60 lbs per 100 feet.

  6. #6
    DIY Senior Member craigpump's Avatar
    Join Date
    Apr 2012
    Location
    ct
    Posts
    717

    Default

    Depends on the PVC couplings. We use sch 1" 120 pipe with sch 120 couplings here all the time down to 700' with no problems.

    The biggest problem you will have using sch 80 is holding it steady & straight up n down while you screw it together. See if you can rent an up z dazy with a halo, it will make life much, much easier and safer too!

    Better yet, call a pump guy with a good solid reputation and have him do it. He has all the equipment, the knowledge, and the job will be guaranteed.

  7. #7
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    490

    Default

    I found myself without my hoist the other day replacing a twin-line jet for a sub. The location was too wet for the truck (38' boom). We screwed all the pipe in on the ground (stainless couplings) and ran it in one string. It's tough to tape the wire good to the pipe doing it like this...but we only had 3 joints. Everything went well. You can use 1" sch 80 PVC...no need for 1.25" pipe unless you're using a high volume pump. A pair of vice grips works really well to hold the pipe for taping etc. Squeeze em down tight, you won't hut the pipe.

    Just make sure you get the wire tight (no slack in the well) and get everything ready first including the well seal at the top (a piece of tape under the well seal will hold it in place. cut the wire 2-3 ft above the well seal and put it through. I always put a junction box right at the well seal anyways.

    Good luck!!

  8. #8
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    490

    Default

    They make it both ways....but the pipe I'm familiar with is sch 80 with male ends on both sides (threaded). They make some stuff that is MXF so you don't need to buy any couplings. I use stainless or brass couplings but you can use galv. if you have good water. If you do use galv. make sure you tape the couplings up. As a rule I avoid putting galv. pipe in a pvc well unless the whole string is galv. Brass/Stainless couplings are about $10-15 retail.

    What is the water level in the well and how much GPM does it make?

    Quote Originally Posted by dENNIS MEYER View Post
    Thanks for the clamp info. I have been trying to find out some information on the pvc pipe not having much luck. I would like to know is it male on one end & femail on the other or are they both male ? I would also like know what the weight per 10, length would be ?

    Thanks

  9. #9
    General Engineering Contractor ballvalve's Avatar
    Join Date
    Dec 2009
    Location
    northfork, california
    Posts
    3,261

    Default

    Wrong pipe. Use Poly 160 psi in ONE piece and slip it all in in one shot.

  10. #10
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    490

    Default

    You'll probably have to special order the 160 or 200 psi poly here in Tx. It's just not carried at many retailers.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •