(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 4 of 4

Thread: Proflex PVC couplings or PVC slip couplings for under slab (in the dirt) wye tie in.

Hybrid View

  1. #1
    DIY Junior Member Pete Horton's Avatar
    Join Date
    Oct 2012
    Location
    Alabama
    Posts
    2

    Default Proflex PVC couplings or PVC slip couplings for under slab (in the dirt) wye tie in.

    everyone says Proflex PVC to PVC shielded couplings are the way to go for under slab wye tie in for a new basement bathroom..but i keep reading they are not rated for direct dirt contact, as they will be under at least 12 inches of dirt with a 4" concrete top poured back over them. Why doesn't a guy use PVC slip couplings to connect? and are the Proflex (or similar type) rated for concealment in dirt?

    http://www.fernco.com/plumbing/shiel...flex-couplings

    PROFLEX SPECIALTY COUPLINGS
    ( Not recommended for direct burial)
    Edit added after reading post below.
    Designed for resistance to heavy earth loads and shear forces, and provides improved pipe alignment.Proflex allows you to make transition pipe connections that are resistant to shear forces, while creating a rigid, long-lasting pipe joint. From 1 " to 8" - PROFLEX connects cast iron, plastic, steel, copper and tubular, drain waste and vent systems.

    PECIFICATIONS


    • Gasket Material: Neoprene
    • Gasket ID: Part No. and application on each gasket.
    • Shield Assembly Material Requirements: All 300 Series S.S.
    • Clamp
      • Band = 301 Stainless Steel .025 x .500 x Length
      • Housing = 301 Stainless Steel - Fernco
      • Screw = 305 Stainless Steel 5/16" Hex - No Slot

    • Shield - 301 Stainless Steel .012 x 2.125 x Length
    • Eyelet - 305 Stainless Steel
    • Installation Torque = 60" lbs.
    • Maximum test pressure: 4.3 PSI (29.6KPA)
    • Maximum operating temperature: 180 F
    • Conforms to the requirement of ASTM C1460

    Last edited by Terry; 10-02-2012 at 01:51 PM.

  2. #2
    Forum Admin, Expert Plumber Terry's Avatar
    Join Date
    Aug 2004
    Location
    Bothell, Washington
    Posts
    14,202
    Blog Entries
    1

    Default

    They are made with stainless steel. We've always used them underground.

  3. #3
    DIY Junior Member Pete Horton's Avatar
    Join Date
    Oct 2012
    Location
    Alabama
    Posts
    2

    Default

    thanks terry. I called Fernco based on "we have always used them" statements from many experts not just you. 20 Years in the army has taught me that is not always a good statement, and usually leads to the truth. Fernco stated they do not recommend their Proflex series for direct burial, if you choose to use them for this they do not stand by the product. They do for their RC series strong back flexible couplings..rated at 50 PSI and direct burial. Now if i could just get you to come bust up my basement floor and install the bathroom. but then id have to hire out the framing, drywall, drop ceilings, cement back fill, stamped concrete touch up where cut out. ext...but with this coupling i can get started. Not wanting to use a gas saw with water in my finished basement..so im going to get a dry blade with my skill saw and have the wife hold the shop vac hose to collect the dust..yes 4" thick..no metal just fiber reinforced.

    http://www.fernco.com/plumbing/shiel...k-rc-couplings
    Last edited by Terry; 10-02-2012 at 01:58 PM.

  4. #4
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,655

    Default

    The make electric concrete saws, but if you want to use a SkilSaw to cut through 4" of concrete, you need at least a 12" blade and several days of sawing. If ProFlex, and other stainless steel banded couplings could not be used in direct contact with the earth, the plumbing business would come to a standstill on the first installation. The problem with "slip couplings" is that you CANNOT work fast enough to install them on a 3" or larger pipe, (it is almost impossible to do it on most smaller sizes also). Once you "screw up" with one there is NO WAY to undo it without just cutting the pipe apart and starting over.
    Last edited by hj; 10-03-2012 at 10:42 AM.
    Licensed residential and commercial plumber

Similar Threads

  1. Is Class 180 sufficient for Couplings?
    By xlr8tion in forum Pumps and Tanks Well Forum & Blog
    Replies: 3
    Last Post: 04-12-2012, 06:42 AM
  2. Water meter couplings
    By tfm825 in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 1
    Last Post: 02-08-2012, 05:15 PM
  3. Water Meter Couplings
    By JasonG in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 09-15-2007, 12:26 PM
  4. No Hub Couplings really work?
    By Geo in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 4
    Last Post: 10-14-2006, 11:11 AM
  5. No Hub couplings
    By Captbwhite in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 6
    Last Post: 04-22-2006, 09:30 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •