(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 5 of 5

Thread: Loosing water pressure....need help!

  1. #1
    DIY Junior Member dhaskins74's Avatar
    Join Date
    Sep 2012
    Location
    michigan
    Posts
    3

    Default Loosing water pressure....need help!

    Type of pump?
    Submersible____XXX____
    Two wire (no control)________
    Three wire (control box)______
    Wire Size_________ Wire Length________
    or
    Jet Pump (above ground)_________
    One or two pipes down the well____

    Size of Pump?
    Motor Horsepower?___1 hp_______
    Pump Model #_2445089003_
    Date Pump Installed_____2009_____

    Pumping from?
    Cistern tank___________
    Pond, lake, river________
    Water Well xxx_______
    Depth of well_195 ft_______
    Depth to water_________
    Pump Setting__________
    Pipe Size_________"
    Drop Pipe Material
    PVC__xxx__
    Steel_______
    Poly________

    Well Recovery Rate_______gpm
    Well Casing Diameter_______
    Rock Well__________ Sand Well__________ Other______________
    Date Well Drilled___2006____

    Well Casing Material
    PVC__xxx___ Steel_________ Other_________


    Pressure Tank?
    Bladder or diaphragm tank (one pipe to tank)xxx_______
    Size or model of tank___Amtrol mod MSS15F100_
    Air charge in top of tank, with pump off and water drained____________PSI
    (check with car tire gauge)
    or
    Plain Hydro Pneumatic tank (two pipes to tank, one in and one out)_________
    Size of tank________________

    Pressure Switch Setting?
    On 30, off 50 ________
    On 40, off 60___x?___
    Other_______________

    Pump Control Method?
    Cycle Stop Valve model #_________
    Variable speed control #__________
    Pump Start Relay (sprinkler timer, no tank)__________
    Manually turned on and off____________

    Pump Protection
    Cycle Sensor_________
    Pumptec_____________
    Low pressure cutoff switch (lever on side)__________
    Other_______________

    Filters or Softeners_____n.a______
    Before or after pressure tank_______
    Type of filter___________________
    Bypass available________________

    Water Used For?
    House Use____x___ Number of baths__3_____ Number of People_6_______
    High Flow Showers_______gpm?
    Plus/Or
    Irrigation with timers________
    Irrigation with hoses________
    Heat Pump___10_gpm?


    Problems Experienced
    No Water_________________
    Water only part time________
    Water at all times but weak_____
    Air in water_______________
    Pressure surging___xxx________
    Water Hammer (noise)______
    Too Much pressure_________
    Other____________________


    Pump makes clicking or buzzing sounds________
    No Sounds______________
    Pressure gauge reading________psi
    Other____________________________________

    Do you have, and know how to use
    an Ampmeter and Voltmeter________no__________

    Describe Problem_Just in the past week we are experiencing pressure drop. Simply running bath water pressure will drop to less than half of normal until you shut it off and let it refill bladder tank. Pressure switch seems to be functioning normaly. First noticed issue a few days ago when our Geo-Thermal unit was running and we couldnt get but a trickle out of kitchen faucet. Faucets run normal if nothing else is going. Geo thermal unit is a Hydro Heat Mega Tech model 03-090-WTAR-TS-AT. When it is running in heat or cool mode at max flow its pulling about 10-12 gallon per minute. I think problem is well related not geo because I can shut unit off and problem is still there. Well is about 6yrs old and Pump was upgraded with larger bladder to a 1hp pump to run the Geo unit 3 yrs ago. Any ideas would greatly help!

  2. #2
    Moderator valveman's Avatar
    Join Date
    Mar 2006
    Location
    Lubbock, Texas
    Posts
    4,156

    Default

    My guess if you have a hole in the pipe somewhere, probably right above the pump. You need a clip around amp meter on an incoming line. If it is pulling 9 amps, you have a hole in the pipe. If it is pulling low amps, your pump is not doing as much as it should.

  3. #3
    DIY Junior Member dhaskins74's Avatar
    Join Date
    Sep 2012
    Location
    michigan
    Posts
    3

    Default hoe in pipe?

    Not doubting or questioning your knowledge but how would you get a hole in the pipe? Could it be caused by wires rubbing or what?

  4. #4
    DIYer, not in the trades LLigetfa's Avatar
    Join Date
    Feb 2011
    Location
    NW Ontario, Canada
    Posts
    3,676

    Default

    Maybe he meant "leak" as PVC is less likely to develop a hole like steel pipe might.

  5. #5
    DIY Junior Member dhaskins74's Avatar
    Join Date
    Sep 2012
    Location
    michigan
    Posts
    3

    Default voltmeter readings

    I borrowed a voltmeter with a loop. I had 8.7 reading on the red wire. Is that close enough to 9 or is 9 a firm number?

Similar Threads

  1. Loosing water pressure
    By vatrader01 in forum Pumps and Tanks Well Forum & Blog
    Replies: 4
    Last Post: 05-28-2011, 07:33 AM
  2. Loosing Pressure
    By johnjh2o1 in forum Irrigation / Sprinkler Forum
    Replies: 0
    Last Post: 04-27-2011, 05:57 PM
  3. loosing pressure sometimes
    By jthomsenrn in forum Pumps and Tanks Well Forum & Blog
    Replies: 3
    Last Post: 07-28-2010, 10:20 AM
  4. loosing pressure?
    By trunpa in forum Pumps and Tanks Well Forum & Blog
    Replies: 1
    Last Post: 04-09-2008, 05:49 AM
  5. Loosing pressure with no demand
    By lazer3691 in forum Pumps and Tanks Well Forum & Blog
    Replies: 16
    Last Post: 12-13-2007, 04:37 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •