(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 10 of 10

Thread: Tailpiece to Trap Rerouting?

Hybrid View

  1. #1
    DIY Junior Member DJL's Avatar
    Join Date
    Sep 2012
    Location
    Ames, Iowa
    Posts
    7

    Question Tailpiece to Trap Rerouting?

    Hello. I'm installing a new double bowl kitchen sink and faucet. We are also strongly considering getting rid of the disposal since we don't use it AND since we are thinking it will provide more usable space in the left cabinet if we get rid of it. Also, note that there is a dishwasher drain line connected to the disposal, though you can't see it in the picture.

    Is there any way to reroute the piping between the tailpiece and trap on the left bowl, so as to maximize usable space on that side of the cabinet? The red line in the picture shows the possible modification I'm talking about. The green line in the picture represents the area I'm trying to free up so I can install a trash/recycling pullout on that side.

    If my idea (red line in pic) is not recommended, then is there any other way to maximize the usable space on the left? There's a lot of space in this cabinet, and it seems a waste to not be able to use some of it.

    Name:  sink.jpg
Views: 201
Size:  57.9 KB

  2. #2
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,434

    Default

    Some places require separate traps, so allow you to utilize one in this situation. If you can get by with only one with your local code, you could cut and cap the trap arm to the left with enough stub to be able to reuse it at a later date, and redo the right-hand one to cross over, connecting both, then dropping to the trap on the right. They make those cross-overs with a baffle so draining one side doesn't back up into the other (more important with a disposer, but an issue with the pump on the DW, too), and you can get them with a DW tailpiece.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  3. #3
    In the Trades Tom Sawyer's Avatar
    Join Date
    Nov 2010
    Location
    Maine
    Posts
    2,946

    Default

    Piece of cake. Pull the disposal and install a new sink basket and a continuous waste and re-use your old P trap. Cap off the unused drain.
    [B]No, plumbing ain't rocket science. Unlike rocket science, plumbing requires a license[B]

  4. #4
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,679

    Default

    Get a 'direct connection" continuous waste and it will be up near the bottom of the sinks and give you maximum space. When you use this, your "red line" will continue to the other drain and connect to it with the included tee. Unless it was really piped to connect that way, twhich would be very unusual, the lower opening should have been a "Cleanout", not a drain connection.
    Last edited by hj; 09-18-2012 at 06:10 PM.
    Licensed residential and commercial plumber

  5. #5
    DIY Junior Member DJL's Avatar
    Join Date
    Sep 2012
    Location
    Ames, Iowa
    Posts
    7

    Lightbulb

    Thank you everyone for your responses. It sounds to me like all three responses point, more or less, to the same solution --> use a continuous waste and cap off or convert the bottom opening to a cleanout. That is assuming that "a crossover with a baffle" is the same thing as a "continous waste"?

    hj, that is an interesting observation about the lower opening probably should have been a "cleanout". I had never considered this. I think I had assumed (without any actual knowledge) that perhaps my city's code required two drain pipes, one to each bowl.

  6. #6
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,679

    Default

    quote; that perhaps my city's code required two drain pipes, one to each bowl.

    That would NEVER be a requirement, and even if it were, the openings would have been arranged differently. I am not sure what you mean by "crossover with a baffle" because that has a specific meaning and would have nothing to do with a sink drain. The continuous waste tee, WILL have a baffle.
    Licensed residential and commercial plumber

Similar Threads

  1. trap tailpiece minimum length
    By stevenrobertburke in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 6
    Last Post: 02-08-2011, 07:39 PM
  2. Tailpiece Trap Primer
    By dlarrivee in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 01-14-2011, 02:51 PM
  3. P trap and tailpiece too close!
    By jdbangels in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 4
    Last Post: 02-09-2010, 04:50 PM
  4. New Sink: 1-1/2" to 1-1/4" Trap to Tailpiece
    By Madera in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 1
    Last Post: 05-04-2005, 08:48 AM
  5. Vent Rerouting
    By hermes in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 04-02-2005, 10:47 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •