Terry Loves Bellevue & Kirkland
425-649-5683, Top Rated Plumber 1-877-808-5683
Results 1 to 3 of 3

Thread: Removed jet pump, installed submersible and now have dirty/orange water.

  1. #1
    DIY Junior Member BKLang2000's Avatar
    Join Date
    Aug 2012
    Location
    DC
    Posts
    1

    Default Removed jet pump, installed submersible and now have dirty/orange water.

    Hello,

    I just completed the installation of a new 10 gallon 1/2 hp submersible with all new parts; i.e. pump, 1" poly, wiring, bladder tank and all of the needed parts. Only thing left that is original is the copper plumbing in the house. We removed a 50 year old deep well jet pump with a galvanized conventional tank. The well is over 200 years old, was hand dug and is lined for the first 30 feet with 2 foot sections of 4" inside diameter terra cotta. The terra cotta sections are not in a straight line, so I purchased a 3" submersible that would fit with limited trouble. The depth of the well is 77 feet, water level is at 42 feet and pump is 6 feet from the bottom. The old jet inlet was 7 feet from the bottom. This setup is located in PA under neath the porch of a house that was built in 1787. The old and now new system was and will be winterized yearly. Upon spring setup we used to get a small orange discoloration in the water. The pump was installed one week ago. We ran the pump to make sure that it was connected correctly and we had plenty of water and pressure. The balance of the system was installed yesterday. After final hookup, we ran the pump, filled some glass jars and the water was clear....a nice surprise given that the old system took a while to settle.
    After filling the hot water tank and bringing the system up to full pressure (40/60), the water started to turn orange. We let it settle for one day, but the water is still orange...quite noticeable in the toilet bowl.

    Please advise,

    Brian

  2. #2
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    386

    Default

    A 1/2 HP 10 GPM sub will pump much more water than any comprable jet pump....so now you're seeing stuff that you wouldn't normally see. Also with a conventional tank you have a little room for settling and with a bladder tank everything that comes in goes out. Keep using it and see if it improves. Good luck.

  3. #3

    Default

    I would also think some of this maybe coming from the insides of your pipes in the house. Over the years the orange has slowly built up and with a stronger system/more pressure it is washing this out of the pipes. You did say it started after you set pressure to 40/60 right? That should clear up after a while as Wellman said.

Similar Threads

  1. Dirty water after installing new submersible pump
    By Guest in forum Pumps and Tanks Well Forum & Blog
    Replies: 3
    Last Post: 09-30-2011, 07:59 PM
  2. dirty water after replacing well pump
    By anitanewman in forum Pumps and Tanks Well Forum & Blog
    Replies: 6
    Last Post: 07-30-2009, 06:59 PM
  3. dirty water after submersible pump replacement
    By jackofmosttrades in forum Pumps and Tanks Well Forum & Blog
    Replies: 6
    Last Post: 10-27-2008, 05:42 AM
  4. Dirty water after well pump replacement...
    By mlblevins in forum Pumps and Tanks Well Forum & Blog
    Replies: 14
    Last Post: 12-20-2006, 11:04 AM
  5. Recirculation pump removed.
    By INTP in forum Plumbing Forum Discussion & Blog
    Replies: 9
    Last Post: 01-14-2006, 07:22 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •