(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 7 of 7

Thread: Toto Toilet

Hybrid View

  1. #1
    DIY Junior Member
    Join Date
    Dec 2005
    Location
    Hungerford, TX
    Posts
    10

    Question Toto Toilet

    I am a builder, and our client (against recommendations) bought a display Toto toliet. It is a 2 piece, and appears to be a Vespin, but we have no ID as yet.

    The toilet came without boxing, instructions and nothing more than the tank and bowl (with all internal parts). The drain is in the back of the toilet about 8" off the floor, a 2"+ intergal porcelin "pipe". The drain outlet (bottom of the porcelin pipe) faces down and not to the rear as a rear drain (retrofit) toilet. The bolt pattern in the bowl is 8-10 O.C., and does not fit a standard toilet flange pattern.

    What have I got? Calls to the vendor with questions have not been answered. My plumber and I can not figure out how to install the toliet.

    I found www.totousa.com, but the Vespin shows a typical bottom drain toilet.

  2. #2
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,434

    Default

    The toilet comes (or should have come) with the unifit adapter. The standard one is for a normal 12" offset. You can get the adapter for either a 10" or 14". Basically, this adapter seats to the normal flange with a wax ring and bolts, plus has 4 additional screws at the rear that need to be installed holding the back of the adapter to the floor. The back of the adapter also has slots for another set of flange bolts. Then, the toilet sits down on top of the adapter, and the toilet bolts to the adapter's bolts, not the normal flange bolts. Since the toilet normally comes with the 12" adapter, and they charge extra for eitherthe 10" or 14", if anyone needed a 10" or 14", the store probably has some 12" ones lying around.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  3. #3
    DIY Junior Member
    Join Date
    Dec 2005
    Location
    Hungerford, TX
    Posts
    10

    Default

    Does the adapter have parts that mate the drain exit (which is 8" off the floor in the rear of the toilet / exiting down) ) to the (typical) floor drain?

  4. #4
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,434

    Default



    The adapter is made to set the toilet over...it mates up with it and seals easily and well. Other than the screws to hold it to the floor, the wax ring, and the flange bolts, it is one-piece plastic. http://totousa.com/ProductPage.asp?pid=159
    Last edited by Terry; 12-20-2005 at 09:29 AM.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  5. #5
    DIY Junior Member
    Join Date
    Dec 2005
    Location
    Hungerford, TX
    Posts
    10

    Default

    Thanks, I checked out the link. As they say "A pic is worth a thousand words." I can see how it works.

  6. #6
    DIY Junior Member
    Join Date
    Dec 2005
    Location
    Hungerford, TX
    Posts
    10

    Default

    Thanks again, the link worked and the part has already been ordered for pick-up this morning. Willing to stay up until 1:30 AM and wait for an answer has paid off. I could not have obtained answers, a solution and saved myself some time searcing this AM if it were not for this forum.

    My plumber if happy and I can get on to other things.

    Junior Member? I am 51 years old?

    Thanks again,

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •