(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 10 of 10

Thread: Delta R1000 installation question.

Hybrid View

  1. #1
    DIY Junior Member bigwooo's Avatar
    Join Date
    Sep 2009
    Location
    BCS Mexico
    Posts
    23

    Default Delta R1000 installation question.

    I'm installing a Delta R1000 rough in valve body into new construction. I'm not a plumber, but because of lack of resources here in Mexico where I'm building, I have to install it myself.

    I have a question about the location of the front of the plastiguard bonnet. The instructions say it should be flush with the wall. Do they mean flush with the unfinished wall, or should it be mounted so that the front of the plastiguard will be flush with the anticipated level of the finished and tiled wall?

    Thanks...again.

  2. #2
    DIYer, not in the trades LLigetfa's Avatar
    Join Date
    Feb 2011
    Location
    NW Ontario, Canada
    Posts
    3,676

    Default

    The manual I downloaded for my R10000 series said the face of the plasterguard should be flush with the finished wall line.

  3. #3
    DIYer, not in the trades LLigetfa's Avatar
    Join Date
    Feb 2011
    Location
    NW Ontario, Canada
    Posts
    3,676

    Default

    I don't know if you typo'd and dropped a 0 so I am going by document DSP-B-T17038_Rev_A_df49.pdf

  4. #4
    DIY Junior Member bigwooo's Avatar
    Join Date
    Sep 2009
    Location
    BCS Mexico
    Posts
    23

    Default

    Thank you...yes, it's a typo. Didn't have my glasses on .

  5. #5
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,624

    Default

    When the face of the "plaster guard" is flush with the "anticipated" FINISHED wall surface, there is a degree of latitude +/- for variations in the final construction.
    Licensed residential and commercial plumber

  6. #6
    Plumber jimbo's Avatar
    Join Date
    Aug 2004
    Location
    San Diego
    Posts
    9,001

    Default

    Note that if you don't install a CARTRIDGE right away with that, you have to install a plug inside, not just the test cap, or you will have hot/cold crossover unitl you put in the cart.

  7. #7
    DIY Junior Member bigwooo's Avatar
    Join Date
    Sep 2009
    Location
    BCS Mexico
    Posts
    23

    Default

    I found the document and downloaded it. That set of instructions is much more detailed than those that came with the valve body. Thank you!

Similar Threads

  1. Can anyone identify this type of Delta Spout and Installation Method?
    By mark1210 in forum Shower & bathtub Forum & Blog
    Replies: 1
    Last Post: 11-24-2009, 05:35 AM
  2. Delta 600 leak question
    By pjsammy in forum Shower & bathtub Forum & Blog
    Replies: 12
    Last Post: 02-18-2009, 10:24 AM
  3. Delta Shower Question
    By Verdeboy in forum Shower & bathtub Forum & Blog
    Replies: 0
    Last Post: 07-14-2007, 10:47 PM
  4. Delta Monitor Question
    By jammin in forum Shower & bathtub Forum & Blog
    Replies: 1
    Last Post: 03-19-2006, 09:41 AM
  5. Delta handle installation on PP stem?
    By jlsmith2004 in forum Remodel Forum & Blog
    Replies: 6
    Last Post: 12-03-2004, 04:46 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •