(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 3 of 3

Thread: UF into watertight box on deck?

  1. #1
    DIY Member ironspider's Avatar
    Join Date
    Jul 2008
    Location
    Michigan
    Posts
    64

    Default UF into watertight box on deck?

    Greetigns all, I've had great advice on my last two questions so I'm back with stage 3!

    Okay, so we're having our deck expanded and when the old deck was torn up it revealed some UF cable running safely along the bottom of a deck joist (stapled to the lower edge of a 2x10) that ran into a sunroom. After having this wire tracked down it turns out it used to control some outdoor lighting that has since been removed (it was replaced with a different lighting layout that is powered and control from elsewhere in the house).

    So, this UF (12/2) is simply diconnected in a box in the basement. It travels outside via an LB in the basement, a short run of conduit, and then exposed along the joist. This part is all underneath a covered section of the deck.

    So, i can simply connect up this wire to the active power feed coming into the box and have power on that cable. I'd like to use that cable to now run the other direction on the deck to the edge of the deck and install a waterproof/watertight receptacle.

    My question is, I know that UF can be run along the bottom edge of a deck since it is not in "danger of damage", and I'd like to avoid running conduit as I don't think it's required [for the long run along the bottom of the joist], but how do I go into the receptacle box? Do I have to use some conduit before I enter the box? Or do they make watertight fittings that can attach directly to the box so that I can run the UF cable straight into the box?

    What I'd really like to do is come straight out from behind the edge joist into the back of a watertight box. So the watertight receptacle box is mounted on the perimeter of the deck but no conduit is.

    Here's a quick drawing of what I'd like to do (on top) and what I'd like to avoid (on bottom):

    Name:  Untitled-1.jpg
Views: 129
Size:  6.2 KB

  2. #2
    Electrical Contractor/Instructor jwelectric's Avatar
    Join Date
    Jun 2007
    Location
    North Carolina
    Posts
    2,523

    Default

    yes come into the back of the box. When you drill the hole through the joist make sure to make it large enough to handle the connector you install into the ko in the back of the box. Also be sure to use the deep box to have room for the GFCI device.

  3. #3
    Electrical Contractor Jim Port's Avatar
    Join Date
    Aug 2009
    Location
    Maryland
    Posts
    156

    Default

    The fitting for the UF will have a compression gland that will tighten down on the cable.

Similar Threads

  1. Tub Drain Not Watertight?
    By Adam123 in forum Shower & bathtub Forum & Blog
    Replies: 1
    Last Post: 07-13-2010, 09:51 AM
  2. setting deck height for deck mount tub fixture
    By jasperx in forum Shower & bathtub Forum & Blog
    Replies: 1
    Last Post: 09-07-2008, 07:56 AM
  3. watertight seal between faucet base and sink
    By mf915 in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 5
    Last Post: 04-20-2007, 06:33 AM
  4. deck
    By Cookie in forum Remodel Forum & Blog
    Replies: 6
    Last Post: 10-08-2006, 06:43 PM
  5. Is toilet/flange joint supposed to be watertight?
    By kwarner in forum Toilet Forum discussions
    Replies: 6
    Last Post: 06-05-2005, 11:40 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •