(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 14 of 14

Thread: Replacing 5 HP submersible pump

Hybrid View

  1. #1
    DIY Junior Member dryman's Avatar
    Join Date
    Jun 2011
    Location
    ECenTEXAS
    Posts
    9

    Default Replacing 5 HP submersible pump

    I have an old 4" well with a 5 hp submersible pump set at 200' (I think). It is on 2" galvanized pipe. The moter has been out for years and I want to replace it. I already purchased a new pump and motor but realized I may have bitten off more than I can handle. I was going to build a tri-pod out of 1 1/2" heavy wall square tubing to pull the pump with but am concerned about the weight I would be pulling. I have a set of 2" elevators for the pipe also. Does anyone have any advice for such a project other than hiring a "professional"? We are in a MAJOR drought here in Texas, all the service companies are busy, and I need the water for my cattle. Any helpful advice would be appreciated. Thanks

  2. #2
    Jack of all trades DonL's Avatar
    Join Date
    Mar 2011
    Location
    Houston, TX
    Posts
    3,644

    Default

    Welcome to Terry's Forums dryman.

    If it is a 5 HP then that sounds like a job for a pro. Are sure it is 5 HP ?

    Have a great day.

    DonL.
    Theory only works perfect in a vacuum.

    Cyber Security Protection for Windows C:\ > WWW.WinForce.Net

  3. #3
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    487

    Default



    There are lots and lots of things a person can DIY. Some save you money, some give you self-satisfaction.

    In my opinion, this is not one of those. I use a rig like the one pictured above. The job can be dangerous. One mistake and you can lose a hand or a finger, or destroy the well. If the pump were to drop it would head to the bottom like a missle and probably destroy the screen.

    What part of Tx are you in?

  4. #4
    DIY Junior Member dryman's Avatar
    Join Date
    Jun 2011
    Location
    ECenTEXAS
    Posts
    9

    Default

    Thanks for the advice, I am located north of Giddings. I am sure it is a 5 hp motor, I used it for irrigation water in the past.

  5. #5
    Jack of all trades DonL's Avatar
    Join Date
    Mar 2011
    Location
    Houston, TX
    Posts
    3,644

    Default

    dryman,

    If It is on 2" galvanized pipe, then Texas Wellman may be correct.

    It would a lot safer to have someone like him to help you.

    You live in Gods country, I have been told.

    Have a great day.

    DonL
    Theory only works perfect in a vacuum.

    Cyber Security Protection for Windows C:\ > WWW.WinForce.Net

  6. #6
    Porky Cutter,MGWC Porky's Avatar
    Join Date
    Jan 2008
    Location
    Virginia Beach, VA
    Posts
    727

    Default

    It can be done by a qualified DIY but like Texas Wellman said, it's best left to the professionals. The possible damaged limbs, pump and destroyed well cost could far exceed the savings. Understood it's costly to have a professional do the job but believe me in this case I recommend it!
    Porky Cutter, MGWC
    (Master Ground Water Consultant)

Similar Threads

  1. SUBMERSIBLE PUMP 110 or 220
    By loudhornsrule in forum Pumps and Tanks Well Forum & Blog
    Replies: 12
    Last Post: 08-23-2010, 10:18 PM
  2. Replacing 32 yearold submersible pump
    By bogdan530 in forum Pumps and Tanks Well Forum & Blog
    Replies: 3
    Last Post: 05-11-2010, 05:54 PM
  3. Submersible pump going bad?
    By psyclemania in forum Pumps and Tanks Well Forum & Blog
    Replies: 7
    Last Post: 08-07-2009, 11:56 AM
  4. Replacing storage tanks with bigger submersible well pumps
    By luc in forum Pumps and Tanks Well Forum & Blog
    Replies: 11
    Last Post: 04-29-2009, 05:56 AM
  5. Replacing submersible pump
    By dirtmover in forum Pumps and Tanks Well Forum & Blog
    Replies: 12
    Last Post: 07-05-2007, 09:17 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •