(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 15 of 36

Thread: Pro's and con's of 4" dia. well

Hybrid View

  1. #1
    DIY Junior Member Shooter45's Avatar
    Join Date
    Mar 2011
    Location
    MS
    Posts
    21

    Default Pro's and con's of 4" dia. well

    I am about to have a new well drilled at our new construction home. What are the pros and cons if any of having the 4" over a 2"? The well will need to be able to satisfy 3 water loving girls at the house. Also should I consider any filters or purifiers?
    TIA

  2. #2
    DIYer, not in the trades LLigetfa's Avatar
    Join Date
    Feb 2011
    Location
    NW Ontario, Canada
    Posts
    3,685

    Default

    Reading the title I thought you were undecided between a 4" and a 6" casing. 2" limits your options way too much WRT deep well pumping. I would advise a 6" casing so that you are not limited with what submersible you can use.

    Filters/purifiers will of course depend on the water quality. I would start by asking the neighbors questions about their wells, how deep they are, where the water table is, and what the water quality is. Ask them if they treat their water and ask for a sample of untreated water to take for analysis.

  3. #3
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,655

    Default

    A pump, depending on ITS size, can get stuck in a 4" casing after several years. Anything smaller could be a disaster when the pump has to be removed.

  4. #4
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    487

    Default

    Sounds like your area is similar to ours. Basically a 2" well is only cheaper when it is installed. A 4" well will give you a much longer pump life, more water, and use less energy. A jet pump is a big energy waster, and you'll be limited to 8-12 GPM, unless you have a really high water level.

    I have very rarely seen a submersible stuck in a 4" well, especially if it's a pvc well. Make sure you use sch 80 PVC drop pipe with good couplings.

  5. #5
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    487

    Default

    Here's why a 4" well is far superior to 2"....

    The submersible pump...
    will never freeze
    will never lose prime
    is water cooled and completely sealed. No bugs to get in the motor, no worries on hot days, and is a lot easier to hide.
    Twice as efficient. My rule is thumb is that a jet to submersible is a 2x deal. In other words, a 1-HP jet would be equivalent to a 1/2 HP sub. Actually it's a little more efficient than that, but 2x makes it simple.
    Much quieter. I doubt you will even know it's running unless you're really paying attention.
    Just in general lasts much longer by my experience.

    The only advantage of the jet pump is that they are cheaper to install and the pump can be serviced without pulling the whole drop-line. On the downside you'll have a jet and leathers/footvalve down in the well that will have to be replaced periodically. Also, since the motors are not sealed and are air cooled they are much more likely to get critters up in there. I have found small snakes, lizzards, and countless dirt dobber nests. Not uncommon for the well to lose prime after the power has been out for a few hours.
    Last edited by Texas Wellman; 03-26-2011 at 08:44 PM.

  6. #6
    Test, Don't Guess! cacher_chick's Avatar
    Join Date
    Jan 2008
    Location
    Land of Cheese
    Posts
    3,151

    Default

    Ask about drilling a 6". If he's got the rig for it the added material cost should be minimal but give you more water and better serviceability.

    There is no reason to plan for anything else until you find out what the water quality and capacity is.

  7. #7
    In the Trades Texas Wellman's Avatar
    Join Date
    Feb 2010
    Location
    SE Texas-Coastal
    Posts
    487

    Default

    I'ver never heard of a 6" well for domestic use in the south. I can't speak for Mississippi but I have a feeling that the 4" well could produce 100 gpm if necessary.

    The whole "stuck pump in 4" is over-blown. We are exclusively 4" here and I have seen very few, if any, stuck pumps in pvc wells. The only exception is if the pump was left to run dead-headed and a few pump malfunctions that were covered by the manufacturer. They replaced the well.

Similar Threads

  1. Connect a fridge. Pro's and Con's of Pex vs Braided Stainless vs Copper vs Plastic
    By geniescience in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 1
    Last Post: 06-16-2010, 11:29 AM
  2. THANK YOU - Terry and all the pro's
    By SpartyRules! in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 1
    Last Post: 09-15-2009, 02:40 PM
  3. "Machine Gun" or "Thud" and a Weeping Toilet...oh my!
    By maxxis in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 7
    Last Post: 03-22-2009, 07:38 PM
  4. Need Whirlpool Recommendation from the Pro's
    By Waltman in forum Shower & bathtub Forum & Blog
    Replies: 14
    Last Post: 10-11-2007, 08:22 PM
  5. Test question for you pro's.....
    By Randyj in forum Pumps and Tanks Well Forum & Blog
    Replies: 11
    Last Post: 06-23-2007, 02:12 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •