(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 10 of 10

Thread: Gas Water heater - low hot water

Hybrid View

  1. #1
    DIY Junior Member amit's Avatar
    Join Date
    Dec 2010
    Location
    Aurora, IL
    Posts
    4

    Default Gas Water heater - low hot water

    Hi,
    This is my first time here and found a wealth of knowledge which made me register and post this.

    I had a RHEEM 50 gallon Gas water heater for about 10 years. Our faucets (sinks and bath tubs) have a single control for hot and cold water. Turn clockwise more and more to get hot water and anti-clockwise for cold water. Lately we saw less and less hot water coming in or we have to turn the faucets way to the max to get enough hot water to last a shower. I thought that the water heater was on its last leg and it might be time to replace it instead of calling someone to open it and see what is wrong (maybe a mistake). Anyway, now I have a brand new Whirlpool Gas Water heater installed, but have the same issue.

    This makes me believe that it is the pipes and not the water heater. Where do I begin? I read about using vinegar to let it clean the sediment from the pipes, some way to backflush the pipes or even checking the dip tube. I am handy, but probably not handy enough to risk a lot of plumbing work.

    What I also found that the cold and hot water pipes coming out of the Water heater are both hot. Should they both be hot? I would expect the cold water pipe to be sending cold water into the heater and would be cold.

    Any thoughts?

    Thank you !!

  2. #2
    Master Plumber Redwood's Avatar
    Join Date
    Dec 2007
    Location
    Connecticut
    Posts
    7,463

    Default

    Sorry to hear that you ripped out a good Rheem and put in a Whirlpoo Water Heater, You could have any number of problems undersized water heater, bad tempering valve, hot/cold cross over, slab leaks, and a few more.

    The hot incoming cold line is caused by convection and is quite normal.

  3. #3
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,633

    Default

    quote; I thought that the water heater was on its last leg and it might be time to replace it instead of calling someone to open it and see what is wrong (maybe a mistake). Anyway, now I have a brand new Whirlpool Gas Water heater installed, but have the same issue.

    That is what often happens when someone "guesses" at the problem and does something before finding out the REAL problem. It IS a mistake, (and I know plumbers who have done the same thing), and often leaves you with less money and the same problem, as you have discovered. There could be a simple explanation, such as a misadjusted temperature limit in the valve, or a failing part in the valve, OR it could be something more extreme, such as a cracked hot water line under the floor if you have a concrete slab house. The only way to solve the problem is to have a plumber come in and make his own tests to find out where, and what, the problem is.

  4. #4
    DIY Junior Member amit's Avatar
    Join Date
    Dec 2010
    Location
    Aurora, IL
    Posts
    4

    Default

    Thank you for the responses.
    @Redwood - Thanks for confirming that the hot coldwater pipe is normal. One less thing to get worried about. Now that I am reading the complaints about the Whirlpool heater, I am more worried as to what to do.
    @hj - Thanks for your feedback. Yes, I know I made a dumb mistake to get things done quickly to avoid issues when it is extremely cold (I am in Chicago). I could have taken my time and done some research. That is what I am trying to do now instead of just calling someone to take a look and follow his suggestions without knowing what is going on.

    Is there anything I can do to confirm what might be happening? I thought it is the hot water pressure that is low, which might be due to the sediment build up in the pipes.

  5. #5
    Plumber jimbo's Avatar
    Join Date
    Aug 2004
    Location
    San Diego
    Posts
    9,001

    Default

    The whirlpool issue is several years old. I have stopped trying to keep up.....but I assume that they have made some changes to improve. It seems they do stand behind in terms of providing parts, etc. But is has been a serious pain for some folks


    Unless you have 50+ year old, galvanized iron pipes, then sediment in the pipes is a non issue. Your problems are probably in the system components...shower valves, faucet cartridges, etc.

  6. #6
    DIY Junior Member amit's Avatar
    Join Date
    Dec 2010
    Location
    Aurora, IL
    Posts
    4

    Default

    Jimbo - It is a 10 yr old townhome community. So, I guess sediment in the pipes is a non-issue.

Similar Threads

  1. question on water heater venting (orphaned water heater)
    By harveymasons in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 08-23-2010, 06:11 AM
  2. Water heater question - cold water, water leaking thru overflow pipe
    By jonyi in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 6
    Last Post: 09-26-2009, 01:26 PM
  3. Water Heater Pressure Relief Valve Leaked About a 2 Quarts of Water
    By hudson in forum Water Heater Forum, Tanks
    Replies: 8
    Last Post: 07-06-2009, 11:51 AM
  4. New water heater, existing water softener, expansion tank needed?
    By dhancock in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 11
    Last Post: 01-12-2009, 08:09 PM
  5. Does a dual water heater installation require that the water heaters be the same size
    By GooSkinBaldi in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 4
    Last Post: 04-29-2007, 02:28 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •