(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 3 of 3

Thread: sink/vanitiy installations

  1. #1
    DIY Junior Member rcspeed's Avatar
    Join Date
    Sep 2010
    Location
    colorado springs
    Posts
    1

    Default sink/vanitiy installations

    Hello,
    I am remodeling a small bathroom. I purchased a 30" long vanity/sink combo from Lowes. When I went to install them, the walls are not square. In fact they are so out of square that when I install the sink so the the back edge lines up with the back wall, the left side of the sink angles out from the wall so far that the front edge has a 3/4" gap.
    Please offer any suggestions on how to account for this and make the installation look good.

    thank you.

  2. #2
    Senior Robin Hood Guy Ian Gills's Avatar
    Join Date
    Jul 2007
    Location
    USA
    Posts
    2,781

    Default

    Don't install the vanity in the corner.

    Or buy a smaller vanity that does not fit to the corner and put a trash can down in that space instead.

    Or find some sort of metal/plastic edging that you can caulk to the top/side of the vanity to hide the caulked gap.

  3. #3
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,397

    Default

    Do they make a similar one, but say 32" wide? YOu could scribe it, then cut it to fit. Do they make optional sides for the top? They are usually about 3/4" thick, and glued to the walls and top, would hide the gap. How much does the top overhang the cabinet? You could cut the existing top to match the angle if there's enough overhang, or cut it a little, then add the optional sidesplashes.

    Or, throw the whole thing away, and get something else that would fit or could be made to fit. A remnant granite piece could be cut to fit and would probably cost $4-500, sink extra, with the sink hole prepared for an undermount sink. Much less for a drop-in sink (polishing the edges is what adds quite a bit to the cost, and a drop-in sink doesn't need to be polished there). Your vanity top is small enough so you may have lots of choices on granite cheap. Go direct to the fabricator, not through a store.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

Similar Threads

  1. More DIY electrical installations
    By jar546 in forum Electrical Forum discussion & Blog
    Replies: 3
    Last Post: 11-25-2009, 05:27 AM
  2. Bath sink faucet with 1.5" base - old sink
    By garym in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 4
    Last Post: 02-12-2009, 06:50 AM
  3. Disposer flange and sink basket in cast iron sink
    By dabiz7 in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 6
    Last Post: 07-18-2008, 01:17 PM
  4. Cost to install pedestal sink vs. cabinet sink in new construction
    By lousygolfer in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 14
    Last Post: 06-24-2007, 12:04 PM
  5. Mysterious black hose connected from wall under my bathroom sink to the sink drainpip
    By joe pipe in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 08-07-2006, 08:20 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •