(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 13 of 13

Thread: portable dishwasher help

Hybrid View

  1. #1
    sales of irrigation, pumps, water wells neili's Avatar
    Join Date
    Sep 2005
    Location
    north dakota/montana
    Posts
    29

    Default portable dishwasher help

    Help. I just got a portable dishwasher. I had some problems hooking up the moen one touch facet to the quick connect and thought that I had it fixed. Then I bumped the faucet and the quick connect flew off. Apparently the plastic threads inside the moen faucet are not strong enough to hold the pressure when the faucet is on or are stripped out. Any ideas how to fix?

    I have one idea. When I use the dishwasher, take off the pull out faucet head and hook my quick connect to the hose that pulls out from underneath the sink. Does anyone know what thread type is on the end of the moen faucet head? Then how do I adapt that thread to faucet thread that is on my quick adapter.

    Find blow up of faucet at http://www.moen.com/shared/pdf/67315pt.pdf

    The part that I would take off and install quick connector on is #1927 spout wand kit.

    Thanks.
    neili
    www.agriindustries.com
    support your local WOW

  2. #2
    Plumber jimbo's Avatar
    Join Date
    Aug 2004
    Location
    San Diego
    Posts
    9,001

    Default

    You would need probably 2 adapters to go from the 1/2" IPS hose fitting to the DW adapter. This would be very inconvenient to do this every time, and you have the potential for a mess when the DW drains to the hose just laying in the sink. Overall, I would get a new non-pullout faucet.

  3. #3
    sales of irrigation, pumps, water wells neili's Avatar
    Join Date
    Sep 2005
    Location
    north dakota/montana
    Posts
    29

    Default more help

    I don't think that the hose has ips thread; it looks more like a much coarser thread. Does anyone know for sure? I realize that I might need to put a new faucet in, but I would like to try this first. If anyone know for sure what adapters I might need that would be very helpful. Thank you. Also where I could get the adapters would be good.
    neili
    www.agriindustries.com
    support your local WOW

  4. #4
    Plumber jimbo's Avatar
    Join Date
    Aug 2004
    Location
    San Diego
    Posts
    9,001

    Default

    You might be right. I think they are IPS, of course they will be straight threads needing a gasket seal, just like the spout has. If they are non-standard in any way, adapters will not exist. Even if is straight pipe threads, this hook up will be problematic. ALso, it will not be to code since laying the hose in the sink will violate backflow prevention on the supply and the drain.

    I am back to the basic recommendation to replace the faucet.

  5. #5

    Default

    I am by no means an expert... but I do have a portable dishwasher. We have our regular faucet like any sink, but for the dishwasher we have a seperate water spicket dedicated to the dishwasher. It is in the place that most sinks have the pull out sprayer. It is convienent because we can run the dishwasher and also use the tap water out of the regular faucet. If you put in a seperate spicket for the dishwasher you could keep the Moen faucet you currently have. Hope that helps.

  6. #6

    Default

    I'm interested to see how you solved this. I have the exact same faucet and the exact same problem. I live in a tiny apartment so my boyfriend has been hooking the dishwasher to the bathroom sink, which I'm less than crazy about and would much prefer to use the kitchen sink. How did this work out for you?

  7. #7
    DIY Junior Member sketchbreaker's Avatar
    Join Date
    Jul 2011
    Location
    Massachusetts
    Posts
    1

    Default

    I cannot believe how frustrating this is. I have the same exact faucet and problem with a portable washer machine. I even requested a custom peice to be made at a local plumbing shop and they could not do it. My only solution was to cut both tubes from the washing machine connector. Put the draining tube in the sink (weight it down so it doesn't squirt on your floor), and i unscrewed the faucet and stuck the metal hose into the cut tube, then i used a C clamp to tighten the tubes together. I have to do this everytime i wash clothes, extremely annoying. No heres the tricky part: i had to time how long it takes for my machine to fill with water so i can set a timer and run to the faucet before the washer stops filling with water, or the tube will shoot off the faucet and squirt everywhere. That faucet will not take the pressure. The bottom line is there is no solution nor part that will adapt to this faucet.. i rent this beach home so i cannot replace the faucet. THIS SUXS!! but atleast it somewhat works.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •