Water Heater Burner Knocks out Pilot...

Users who are viewing this thread

Waldo_VT

New Member
Messages
4
Reaction score
0
Points
0
Hello All

Well my gas water heater pilot light will not stay lit and I did a bit of investigating and I think I found the problem but I do not know how to fix it. Apparently when the burner comes on the pilot light goes out. After lighting the pilot I will slowly turn the temperature know up until the burner lights. Then when I turn the temperature know down the burner shuts off but the pilot is out. When lite the pilot flame is a good strong blue with some slight orange hitting the tip of the thermocouple.

What can I do?

Thanks again.
 

Waldo_VT

New Member
Messages
4
Reaction score
0
Points
0
New Thermocouple

Thanks but I have already replaced the thermocouple.
 

Toolaholic

General Contractor Carpenter
Messages
894
Reaction score
6
Points
18
Location
Marin Co. Ca.
adjust the pilot lite flame up higher, if possible

some gas appliances have a small ajusting screw. look on the regulator out front. also tighten, if necessary the small pilot fitting going in to same control
 

TheZster

Member
Messages
249
Reaction score
0
Points
16
Location
Fort Collins, Colorado
Had a similar problem last year - it required replacing the thermocoupler - twice....... first one was defective...

Though it sounds as if the burner lighting up is blowing out the pilot - and it's not re-lighting
 

Master Plumber Mark

Sensitivity trainer and plumber of mens souls
Messages
5,533
Reaction score
354
Points
83
Location
indianapolis indiana - land of the free, home of
Website
www.weilhammerplumbing.com
New gas teromstat

the high limit switch is burnt out in the gas thremostat.

they cannot be repaired ,
and arent meant to be messed with
so you need a whole new gas thermostat

costs about 65 bucks...


what brand of water heater is it???

if you got a whirlpool, it might be trouble...

a small tip

remember to turn water off first before unscrewing valve..
 
Last edited:

Waldo_VT

New Member
Messages
4
Reaction score
0
Points
0
Thezster,

Yes you are correct the burner lighting up is blowing out the pilot and it is not re-lighting.

MPM:

Why do you think the high limit switch is burnt out in the gas thremostat? I thought that a burn out high limit switch would keep the burner and pilot from even lighting up? BTW it unit is a very basic 40gallon shorty State Select water heater ~8-9 years old.

Thanks you for the responses
 

Master Plumber Mark

Sensitivity trainer and plumber of mens souls
Messages
5,533
Reaction score
354
Points
83
Location
indianapolis indiana - land of the free, home of
Website
www.weilhammerplumbing.com
I see it every day

Again I ask

WHAT BRAND ARE YOU TALKING ABOUT?????????


If the thermocoupling wont work its just the next step..to try...

----barring some exotic vent problem
you see once in a blue moon... or

you could have a bad orfice in the burner assembly,
but usually we only see that kind of problem it the unit
has been under water


you got to just assume its the hermostat that is the problem..

They cant be repaired
so you just got to trust that its the problem....
it cant be anything else, cause their isnt anything
else it can be


we just went down this road today....with a Bradford White unit

changed out a thermocoupling a few weeks ago now its
going out again....sent one of my guys down ther ewith
a thermostat and changed it out....


its all trial and error.. good luck...
 
Last edited:

Waldo_VT

New Member
Messages
4
Reaction score
0
Points
0
Thank for the help

MPM

The unit is a "State Select" shorty 40 gallon water heater.

Thanks again
 

Master Plumber Mark

Sensitivity trainer and plumber of mens souls
Messages
5,533
Reaction score
354
Points
83
Location
indianapolis indiana - land of the free, home of
Website
www.weilhammerplumbing.com
Now---how Old?????

Is the unit a pre-2003 water heater or the new
sealed combustion type.....
with the sparkey push button type
ingniter???.

If it is the newer style with the sealed combustioin feature
you got troubles.....

they are trouble


get the serial number off the unit, it should tell you how old it is
 

Jadnashua

Retired Defense Industry Engineer xxx
Messages
32,770
Reaction score
1,190
Points
113
Location
New England
He indicated it was 8-9 years old. It might be more cost effective to replace it...it's on it's last legs in all likelyhood. My unprofessional opinion.
 

RioHyde

Plumber
Messages
339
Reaction score
0
Points
0
Location
Cincinnati, Ohio
I'm with Jadnashua. Since its 8-9 years old and giving you that much of a headache replace it before it soaks you.
 
Top
Hey, wait a minute.

This is awkward, but...

It looks like you're using an ad blocker. We get it, but (1) terrylove.com can't live without ads, and (2) ad blockers can cause issues with videos and comments. If you'd like to support the site, please allow ads.

If any particular ad is your REASON for blocking ads, please let us know. We might be able to do something about it. Thanks.
I've Disabled AdBlock    No Thanks