(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 14 of 14

Thread: Repair or replace?

Hybrid View

  1. #1
    DIY Junior Member adamw's Avatar
    Join Date
    Jan 2008
    Location
    Pennsylvania
    Posts
    26

    Default Repair or replace?

    I have a Bradford White WH manufactured January 1999. It has been in service since May 1999. Yesterday morning while showering, I had to start out with the faucet turned further than usual. During my ten minute shower, I had to keep turning it further and further hot to keep it warm enough. This has never happened before yesterday morning. Nothing else was different. No one else (or nothing else) was using water at the time. My wife experienced the same issue later in the day, and I experienced it again this morning.

    After doing some research online, it seems that the likely culprit is the dip tube. The burner burns, there are no leaks. It seems that replacing the dip tube is something I can easily accomplish myself. (I think the hardest part will be draining some water out without it getting all over the floor. It's in a basement, so I can't easily run a hose from it to the outside and there are no drains lower than the spigot.)

    I found a local plumbing supply store that has a dip tube. It's 6 bucks.

    So my question to you all is, do I bother trying to fix this 10+ year old WH, or just bite the bullet and buy a new one?

    Thanks!

  2. #2
    Retired Defense Industry Engineer jadnashua's Avatar
    Join Date
    Sep 2004
    Location
    New England
    Posts
    21,434

    Default

    Gas or electric? If electric, you sure the elements are working? A dip tube may not be that hard to replace...depends. While you are at it, you might change the anode rod too. At 10-years, thoughit could be beyond it's livespan.
    Jim DeBruycker
    Important note - I'm not a pro
    Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013, 2014

  3. #3
    DIY Junior Member adamw's Avatar
    Join Date
    Jan 2008
    Location
    Pennsylvania
    Posts
    26

    Default

    It is gas. And yeah, I thought about the anode rod too.

  4. #4
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,679

    Default heater

    A bad dip tube should have given you about a 3 minute shower and then it would have been cold. There would have either not been any gradual change or if there were it would have happened very rapidly. Not sure what the problem could be without checking it personally, but after 9 years it is a crap shoot whether it is worth fixing. OR, if the fix would even cure the problem.

  5. #5
    DIY Senior Member Runs with bison's Avatar
    Join Date
    Aug 2009
    Location
    Midwest
    Posts
    892

    Default

    It is worth trying to service it yourself. Beats the expensive crapshoot of calling a plumber who will charge several times more just for the call than you would have in it DIY. Have you ever blown it down? If you pull out the old dip tube and anode and find nothing wrong, then you will have a mystery.

    Have Plan B replacement option ready.

  6. #6
    In the Trades Gary Swart's Avatar
    Join Date
    Sep 2004
    Location
    Yakima WA
    Posts
    7,246

    Default

    Checking the dip tube is a pretty simple operation. As HJ indicates, it is likely not the problem, but on the other hand, 1999 was at the end of the rash of defective dip tubes. If it is the dip tube, less than $10 will replace it and buy you some time. A failed dip tube leaves debris that can never be completely flushed, but you have nothing to risk and at least you will know.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •