(206) 949-5683, Top Rated Plumber, Seattle
Page 1 of 2 12 LastLast
Results 1 to 15 of 22

Thread: Cant disconnect pitless adapter

  1. #1

    Default Cant disconnect pitless adapter

    I've got a leak or bad check valve and need to pull up my pump.I've never done this before but last time I had this same problem it cost nearly 2000.00.It was just a rusted nipple but I was told I should opt for a new pump,What a rip.Anyways I couldn't figure out the pitless connection but what I'm looking at online seems as if mine is of the "cable"or "spring" type.There is no cable on it but it has a piviting lever that contacts the side of the well.I pulled and pryed as hard as i could like an idiot until I noticed the lever.I tryed to make a hook out of some old copper tubing that was laying around but no luck.What should I do to unhook this thing? Am I on the right track??The well has been running all summer on 5 sec. off 15 sec. 24/7.I thought this was the case but only verified the problem after a 300.00+ electric bill.Thanks for any help you can offer

  2. #2

    Default

    Not sure about your pitless. On mine all I do is thread a pipe into the top of it and pull up the pump. What I can tell you a motor will not survive long continuously short cycling like that. You should have disconnected it the minute you noticed it. The fact that yours is still running after doing that for a month is kind of surprising to me. In any event when you do pull the pump you might as well replace it or expect to be pulling it again real soon.

    -rick

  3. #3

    Default

    I'm hoping its going to be so easy once I figure this dang thing out that I'll replace the pump next time.The last time this happened the pump was 15 years old and it did the same thing for months.It was still working fine and only replaced it on recommendation of well company.I'm sure I'm pushing my luck but just can't spend the money right now.Doesn't anyone have a suggestion on how to "release" this pitless connection?

  4. #4
    CT pump guy Teets's Avatar
    Join Date
    Aug 2007
    Location
    Watertown, Connecticut
    Posts
    87

    Default

    I'd look at that last $2000 invoice and see if they made any special notations on it as to pulling the pump in the future. If this is what I think it is it's referred to as a spider pitless and can be a pain in the butt to remove. Normally there is a steel cable that you can pull up on to lift up the rear leg so the adapter can be pulled to the rear of the casing and then lifted up out of the well. If not I would see if there's a way you can make up a hooked device to pull up on this rear leg to be able to pull the pitless back and then out of the well. Let us know.

  5. #5

    Default

    After I make up a hook and lift the leg will the adapter slip apart or am I going to have to make up something to pry it apart also?

  6. #6
    DIY scratch-pad engineer leejosepho's Avatar
    Join Date
    Nov 2006
    Location
    200 miles south of Little Rock
    Posts
    2,474

    Default

    ... thread a pipe into the top of it and pull up the pump.
    Whatever else you do, be sure to have a good grip on that pipe before releasing the adapter!

  7. #7
    That's all folks! Gary Slusser's Avatar
    Join Date
    Aug 2004
    Location
    Wherever I park the motorhome.
    Posts
    6,792

    Default

    Always make that pipe into a Tee handle that is wider than the casing by a few inches so the handle overhangs each side of the casing.
    Gary Slusser Retired (= out of business)
    Click Here to learn how to correctly size or program a water softener.
    CAUTION, as of Nov 12 2013 all YouTube videos showing how to rebuild a Clack valve have an error in them that can cause damage.

  8. #8
    Master Plumber nhmaster's Avatar
    Join Date
    Jul 2008
    Location
    S. Maine
    Posts
    2,039

    Default

    This is most likely what you have down the well. A standard pitless puller will not work. You need to have both the cable that pulls the latch up and the cable that keeps the pipe from falling down into the well. If the latch cable is not there you will need to fabricate a hook. Also make sure there is another strong cable attached to the drop pipe. You may very well want to have a well company come out and do this as they will have the hook.
    Attached Images Attached Images  

  9. #9

    Default

    Thanks for all the info.I made up a hook today at work I hope it will be strong enough to lift the lever and release the adapter.Theres already a "t" on the end of the upright pipe so I cant possibly drop it into the well.I havent decided if I want to try this after work or wait until the weekend.Who knows what part/parts I'll need and theres no plumbing supply nearby.I hate the idea of leaving it as is until Saturday though.If its the check valve is it usually pary of the pump or seperate? Is there a certain brand/type I should get? Thanks again,Gary

  10. #10
    That's all folks! Gary Slusser's Avatar
    Join Date
    Aug 2004
    Location
    Wherever I park the motorhome.
    Posts
    6,792

    Default

    Usually submersible pumps have an internal check valve but some don't and you add one on the outlet. You want a high quality one in brass.
    Gary Slusser Retired (= out of business)
    Click Here to learn how to correctly size or program a water softener.
    CAUTION, as of Nov 12 2013 all YouTube videos showing how to rebuild a Clack valve have an error in them that can cause damage.

  11. #11

    Default

    The adapter I have looks similar to that drawing.The "actuator" lever doesnt appear to have ever had a cable on it. I've tried everything to get this dang lever to release but I'm not sure if it needs to go up or down.I made a hook and tried every thing I could think of with no luck.Any suggestions?

  12. #12

    Default

    I don't know if these pictures will help but you can see what I have although blurry

  13. #13

    Default

    http://s567.photobucket.com/albums/ss112/63split/well/ Hopefully this time all three will come up.I'm not too familliar with this stuff.

  14. #14
    That's all folks! Gary Slusser's Avatar
    Join Date
    Aug 2004
    Location
    Wherever I park the motorhome.
    Posts
    6,792

    Default

    No help here, I've never seen anything like that before. Maybe you have to pick up the weight of the pipe/pump before it will 'unlatch'.
    Gary Slusser Retired (= out of business)
    Click Here to learn how to correctly size or program a water softener.
    CAUTION, as of Nov 12 2013 all YouTube videos showing how to rebuild a Clack valve have an error in them that can cause damage.

  15. #15

    Default

    I've used a prybar,tried turning it with a pipewrench,tapping with a hammer while prying.I've tried both lifting and pushing down on the lever but it doesn't move.I'm afraid I'll break it and really be screwed.I've searched the web to try to get a better idea of how its supposed to work but I havent found anything like this piece of crap.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •