I have an 18" dishwasher ordered and on its way. The standard size will not fit.
I'd like to go ahead and get the space cut out. I have the dimensions and a saws-all to make the cuts. The red square in the foto is where she's going. My foremost question is how far down to I make the hole? Do I go ahead and cut all the way down to the linoloeum? There has never been a dishwasher in this house so it is a from scratch job.
Any advice is greatly appreciated~
That's where the sawzall will come in real handy to take care of the oven door handle.
I just post cuz I like to see my avatar.
Your cut needs to be neat, so a recip saw would not be a good choice. The hand saw with fine teeth would be best, but jig saw with a fine tooth blade would also make a smooth cut. I would not cut anything until I had the installation plans in front of me. Then measure at least twice before cutting. Cut it too big and you'll have a real problem.
Most brands...you can download the install manual and specs from their website. I would get that and have a look before you start cutting.
Other than that, fairly straightforward as the sink is right there for water and drain. How about power? Where will you get that, since if there is power under sink for disposer, it is SWITCHED.
Back to the drain? What code are you under? Many areas REQUIRE and air gap, which means a new hole in the sink top. OOPS......I see you have no room for a new hole, but you will have to lose the sprayer or the soap dispenser
With the range pulled out, it seems like a pretty easy task to pull out the blind corner cabinet and disassemble it carefully to get a nice cut. You may even be able to flip the front panel and get a good factory cut edge. Or cut at the door opening and the blind end, that way only a few inches of your cut will be exposed.
If you're lucky, look carefully at the stiles where that cabinet to be removed and the sink base connect. You may find that there are some screws and you can remove them, and then the cabinets will come apart...no cutting at all. If they were built in place, then the face frame may be all one piece, and that won't work. Can't tell from the picture. There may be backing for the countertop that is screwed into the cabinet. That may be the hardest thing to remove. Again, if you're lucky, you might find that you can just leave that and the DW might slide in with it still attached.
Important note - I'm not a pro
Retired Defense Industry Engineer; Schluter 2.5-day Workshop Completed 2013
Get your head inside the cabinet and look around. You need to be sure of where the cabinets are separated. It looks like the left side red line should be where the side of the sink base cabinet is. Don't cut where you don't have to.
If the cabinet is laminate or ply,use a laminate blade in the saw (the teeth are reversed to cut on the inward stroke). Use a straightedge clamped to the front of the cabinet as a guide to get a straight cut. You can install new laminate edging around the cut opening.
Dishwasher steam will find it's way into the cabinet space and can cause moisture problems. Everything in the opening should be sealed with a good oil-based paint.
The dishwasher should be flush with the face of the cabinets when it is installed so the cut edges should not be visible, so no need to worry about whether they are stained or not.
I appreciate all your advice. I am tackling this project this week and may be posting other questions. Thanks for all your input.
My dad and dishwasher are rolling down I-40 as I sit here.... I am trying to get a few things ready. Again, this is a dishwasher (18") installation from scratch, this house has never had one. I'm planning to use the hot water line coming up from beneath the house. I already realized that I got a wrong part. Is there such a fitting/part that would screw onto the existing gatevalve that would have a tee- one for the dishwasher feed and the other for the sink hot water tap?
So far so good, like the branch tailpiece you got.
These work well without having to get a three way stop.
If big orange or blue don't have it, try a plumbing supply house.
I just post cuz I like to see my avatar.