(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 15 of 23

Thread: Is methane dangerous when cutting cast iron?

Hybrid View

  1. #1
    Programmer mbauer's Avatar
    Join Date
    Jan 2009
    Location
    Dallas, TX
    Posts
    8

    Default Is methane dangerous when cutting cast iron?

    Hi all! I found myself here by way of the John Bridge tile forum. I'm doing a bathroom renovation on a 1950's slab foundation in North Texas. I'm wanting to go back in with a Kerdi drain and waterproofing membrane. In preparation for it, I'm wanting to replace the existing trap with PVC. In the attached pics you can see what I have. I'm basically wanting to cut it right behind the bell with a carbide tip blade in my sawzall and transition with a Fernco connector into the PVC trap.

    So, as my question says, is methane a danger when cutting cast iron? I really don't want my first big plumbing project to end in disaster. Any other comments or suggestions are more than welcome.

    Thanks!

    Matt
    Attached Images Attached Images   

  2. #2
    Forum Admin, Expert Plumber Terry's Avatar
    Join Date
    Aug 2004
    Location
    Bothell, Washington
    Posts
    14,202
    Blog Entries
    1

    Default

    No worries about gas.
    The roof of your home has plumbing vents that prevent buildup of gas.

    Plumbers use couplings with a shielded couping to prevent the pipes from shifting like these


  3. #3
    Programmer mbauer's Avatar
    Join Date
    Jan 2009
    Location
    Dallas, TX
    Posts
    8

    Default

    Thanks Terry. I'm going to have a few more questions about this project before everything is done. Could you change the title of the thread to "1950's Bathroom Renovation"? I guess you might want to move it to the renovation or shower forum as well. I'll keep all other related questions here.

    I thought I had seen a comment in the tile forum regarding the fernco connector. They mentioned that using a flexible connector gives a little more ability to adjust the final level of the Kerdi drain. With the drain slope, I'm assuming a more rigid connection would make my final level a little bit off. Maybe I'm splitting hairs and the final shower pan that I build will even it all out?

    Thanks!
    Last edited by mbauer; 01-12-2009 at 10:06 AM.

  4. #4
    DIY Senior Member gardner's Avatar
    Join Date
    Apr 2007
    Location
    Ontario
    Posts
    217

    Default

    Quote Originally Posted by mbauer View Post
    I'll keep all other related questions here.
    CX and the gang have you well trained, don't they?

  5. #5
    Programmer mbauer's Avatar
    Join Date
    Jan 2009
    Location
    Dallas, TX
    Posts
    8

    Default

    Ha! Yea, I don't want to ruffle any feathers over here too.

  6. #6
    Forum Admin, Expert Plumber Terry's Avatar
    Join Date
    Aug 2004
    Location
    Bothell, Washington
    Posts
    14,202
    Blog Entries
    1

    Default

    I kind of like the title.
    It's a good question.

    Before I became a plumber, somone was trying to scare me about removing the toilet in a bathroom.
    Nobody even notices all of those pipes coming up through the roof.

  7. #7
    DIY Senior Member Nate R's Avatar
    Join Date
    Jan 2007
    Location
    Milwaukee, WI
    Posts
    472

    Default

    Quote Originally Posted by Terry View Post
    No worries about gas.
    The roof of your home has plumbing vents that prevent buildup of gas.

    Plumbers use couplings with a shielded couping to prevent the pipes from shifting like these

    So this doesn't happen:



    If you think this looks bad, imagine this on the horizontal, the waste has to hop up and over to get by.
    Nice picture.
    Terry
    Last edited by Terry; 01-14-2009 at 10:09 AM.

  8. #8
    Junior Member
    Join Date
    Jan 2009
    Location
    East Slope of the Rockies
    Posts
    9

    Default

    Quote Originally Posted by mbauer View Post
    I'm basically wanting to cut it right behind the bell with a carbide tip blade in my sawzall and transition with a Fernco connector into the PVC trap.
    I've given up cutting cast with saws. What a frustrating experience. If I need to cut cast, I use a soil pipe cutter. Google RIDGID Model 246 Soil Pipe Cutter and you can see the one I rent as needed - it's worth every penny and then some. Last 4" cast I had to cut took me about 3 minutes.

    If a guy can borrow one so much the better.


    RIDGID Model 246 Soil Pipe Cutter
    Last edited by Terry; 01-14-2009 at 10:14 AM.

  9. #9
    DIY Member edlentz's Avatar
    Join Date
    May 2008
    Location
    Michigan
    Posts
    70

    Default

    Rugged--

    The pipe was gone. It was messy though! Really old CI I am married to a wonderful woman who has Chrons disease and believe me when I work on the waste systems in the house I need to get it back in service in a hurry!

    The blade I bought was crap. I also found other uses for the diamond blade for the angle grinder (like cutting tile). So the expense hasn't been just for that job.

  10. #10
    Master Plumber Dunbar Plumbing's Avatar
    Join Date
    Apr 2005
    Location
    Northern Kentucky/Greater Cincinnati Area
    Posts
    2,943

    Default

    Wow,


    Sorry to hear of your bad experience with a diamond blade. I've been using them for years. It happened by accident in using one one day when I was in a jam and didn't have my wheeler chain snap cutter.


    It allows me to cut cast iron that is thinning at the top or bottom and not crush it all in when the chain clamps down on the pipe.


    I use it to cut tiled walls when doing shower faucet reworks, along with cutting copper piping whether it is water or dwv when you just have to save a pipe or can't get a cutter in there to spin around.

    Chrons disease is a rough one. Have you considered one of Terry's bidet toilet seats?

    It will pay itself off in the toilet paper you use at your home, I promise. Lot less clogs and cleaner feeling.


    I've had one since last year *BB-50* and even though it's the most economical, I am a bed of fresh daisies between my legs now, in my nooks n' crannies so to speak. I thought I'd let everyone know how clean I am.
    Read what the end of this sentence means.

  11. #11
    DIY Member edlentz's Avatar
    Join Date
    May 2008
    Location
    Michigan
    Posts
    70

    Default

    Yeah some tools work well for some and not so much for others. I use my Recip saw alot for other things. Also , there was too much info in that last message from you Rugged! Although we just redid the bathroom and I had never thought of a Bidet! Maybe that will come.

    Thanks

  12. #12
    Master Plumber Dunbar Plumbing's Avatar
    Join Date
    Apr 2005
    Location
    Northern Kentucky/Greater Cincinnati Area
    Posts
    2,943

    Default

    Quote Originally Posted by edlentz View Post
    Yeah some tools work well for some and not so much for others. I use my Recip saw alot for other things. Also , there was too much info in that last message from you Rugged! Although we just redid the bathroom and I had never thought of a Bidet! Maybe that will come.

    Thanks

    It was the Thomas's English Muffin reference, wasn't it.



    You know how much toilet paper you use knowing how that disease works. It's very awkward at first, but it's like a mini-shower on demand and can make the reach around process obsolete. The ones with a dryer and warm water are top notch, I just haven't graduated to that level yet. It's coming!
    Last edited by Dunbar Plumbing; 01-15-2009 at 09:00 AM.
    Read what the end of this sentence means.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •