(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 11 of 11

Thread: High Water Pressure

  1. #1

    Default High Water Pressure

    I understand that having high water pressure results in higher water bills, banging pipes and appliance breakdowns. However, there is a huge difference in comfort when using faucets and showers at 120psi as oppose to 50psi especially when multiple showers, faucets or toilets are in use at the same time.

    Our house has static water pressure of 120psi but when I adjust our pressure reducer valve to make it 50psi, the pressure is way too low and aggrevating when multiples are in use. I have tried it at 80psi and still a little aggrevating. Our house pipes do not bang and our appliances work fine. So, is it OK for me to leave it at 120psi? Our water heater has an expansion tank that is pre-charged at 70psi. Is it true that you should not go more than 80psi. What problems may occur by pre-charging so high?

    Please advise. Thank you!
    Last edited by Mikeyboy; 11-30-2008 at 05:10 PM.

  2. #2
    Master Plumber master plumber mark's Avatar
    Join Date
    Feb 2005
    Location
    indianapolis indiana - land of the free, home of the brave....
    Posts
    4,243
    Blog Entries
    1

    Talking Do whatever you want to

    their is no reason you cant do whatever you
    want to in your own home...



    if you dont like it at 80 psi, cause you like to be
    sandblasted by multiple shower heads in your shower
    that is your choice..



    things will simply last longer if you kick it
    down to 60--70 psi.....



    ballcocks, washing machine hoses and water heaters
    simply live longer with the lower water pressure..

    if you are going to leave it at 120.


    I suggest that you be sure that your washing machine hoses are braided SS ones.

    eventually the expansion tank on your heater will blow a gasket seal inside ...

    I hope that your pop off valve is going to a good floor drain for the
    day it finally blasts loose...probably at night this will happen.....

    so just be sure to pipe that line somewhere



  3. #3

    Default

    I guess this explains why I had to replace my expansion tank within 2 years of installing it. It waterlogged. I am currently using a 2 gal expansion tank, is it better to get the 5 gal given by high pressure scenario? Does pre-charging it at a higher rate prolong the life of the tank?

    Won't the expansion tank prevent the t&p valve from getting damaged?

    The t&p valve pipe is already piped to a floor drain.

  4. #4
    Master Plumber Redwood's Avatar
    Join Date
    Dec 2007
    Location
    Connecticut
    Posts
    7,463

    Default

    Lowering the water pressure below 80 PSI will significantly increase the service life of all your plumbing system components.

    That may be why most codes that I know of specify 80 PSI Max. Anything above that requires the installation of a pressure reducing valve.

  5. #5

    Default

    What about my questions regarding getting a 2 gal or 5 gal expansion tank?

    Is it better to get the 5 gal given by high pressure scenario? Does pre-charging it at a higher rate prolong the life of the tank?

    Is there a better manufacturer for expansion tanks or do they all work the same? Lowes sells Wellsaver. Home Depot sells Watts.

  6. #6
    Master Plumber Redwood's Avatar
    Join Date
    Dec 2007
    Location
    Connecticut
    Posts
    7,463

    Default

    It is better to lower your water pressure to less than 80 PSI.
    That is my final answer.

  7. #7
    In the Trades Gary Swart's Avatar
    Join Date
    Sep 2004
    Location
    Yakima WA
    Posts
    7,246

    Default

    My first and final answer is that 60 psi is plenty of pressure in a home. More than that will shorten the life of appliances, hoses to appliances, and the fixtures that have to hold back the excessive pressure. High pressure will not increase your water bill directly, you only pay for the volume of water you use regardless of the pressure. If you have a volume problem, clean the aerators in you shower heads, sink spouts, and washer. If the lines are plugged, more pressure isn't the answer.

  8. #8
    Master Plumber master plumber mark's Avatar
    Join Date
    Feb 2005
    Location
    indianapolis indiana - land of the free, home of the brave....
    Posts
    4,243
    Blog Entries
    1

    Talking probably a waste of money and time

    Quote Originally Posted by Mikeyboy View Post
    What about my questions regarding getting a 2 gal or 5 gal expansion tank?

    Is it better to get the 5 gal given by high pressure scenario? Does pre-charging it at a higher rate prolong the life of the tank?

    Is there a better manufacturer for expansion tanks or do they all work the same? Lowes sells Wellsaver. Home Depot sells Watts.

    you would have to pump the tank up to 120 just to get equal balance between the pressures..

    its probably just a waste of money, but it is your money...

    I am sure their are other factors involved with your decison
    for high water pressure in the shower...

    their should not be more than two people in a shower at the same time...

    but I dont think their is any code about that....





    .

  9. #9
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,605

    Default tank

    There is only about a few of spoonsful of water involved to create a large amount of thermal expansion so the size of the tank, and to a large degree the air pressure charge is immaterial. The only thing that will happen is that the greater the disparity between the air pressure and the system pressure the more water there will be in the tank, which could create a weight problem if it is not securely supported. The real problem with 120 psi water pressure is the tendency for faucet and toilet supply lines to rupture and flood the house.

  10. #10
    Master Plumber master plumber mark's Avatar
    Join Date
    Feb 2005
    Location
    indianapolis indiana - land of the free, home of the brave....
    Posts
    4,243
    Blog Entries
    1

    Talking high water pressure

    took out this water heater on satruday...and I noticed the pipes were bent way inwards....

    I am not sure wether the thermostat overheated this
    heater and it was about to explode

    or the warping of the pipes on top of it were
    from high water pressure...


    they had about 98lbs psi..




  11. #11
    Plumber Winslow's Avatar
    Join Date
    Dec 2005
    Location
    Hawaii
    Posts
    450

    Default

    you should not have a pressure volume drop after opening multiple faucets. If you are then the PRV needs to be replaced. When working correctly a PRV will compensate and keep the volume flowing when additional faucets are opened.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •