(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 8 of 8

Thread: Need suggestions

  1. #1
    DIY Member edlentz's Avatar
    Join Date
    May 2008
    Location
    Michigan
    Posts
    70

    Default Need suggestions

    I am remodeling my kitchen. I have almost all the electrical done but the undercabinet light wiring is baffling me. I purchased some LED light sticks. Basically they are 19" long with a double line of bright white LEDs. they use 120vac so there aren't any transformers. They surface mount and have a hard wired plug on one end. So the question is, how would any of you guys install these. I have run a switched circuit for them. I have thought about putting a box in the upper cabinet with a small grommet and making a splice to the power that way. What would you all do? I would like to hide as much as possible.

    Thanks

  2. #2
    In the Trades Master Plumber 101's Avatar
    Join Date
    Aug 2008
    Location
    Wisconsin
    Posts
    268

    Default

    I'm not a sparky for good reason, but I can tell you what I've seen sparkys do. Where your connection is they will stub out of the wall as high as possible underneath cabinet with ROMEX® 14-2. Make sure enough ROMEX® is stubbed out of wall. BE ADVISED I AM NOT A SPARKY ONLY RELAYING WHAT I HAVE SEEN ON JOBS. Good luck!
    Last edited by Terry; 12-07-2011 at 10:20 AM.

  3. #3
    DIY Member edlentz's Avatar
    Join Date
    May 2008
    Location
    Michigan
    Posts
    70

    Default

    Thanks for the suggestion. I have thought of that but how do they make a connection without a box or a wiring enclosure? My lights have only a plug.

  4. #4

    Default

    Here is what I did in my kitchen remodel almost 2 years ago. I installed an outlet in the cabinet above the sink. I then had each outlet wired to be controlled by a different switch. You can see the switches to the right of the sink. On outlet controls the floursecent light above the sink and the other switch is for the under cabinets lights (whenever we both can decide on which ones to install).
    Attached Images Attached Images     

  5. #5
    DIY Member edlentz's Avatar
    Join Date
    May 2008
    Location
    Michigan
    Posts
    70

    Default

    Thanks for the pics Chestnuts. That is pretty much what I thought I would have to do, and I have wired something like that already. I am hoping to come up with a more concealed idea. Having a outlet in the cabinet isn't pleasing the missus.

  6. #6
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,605

    Default light

    What kind of connection is the wire into the light. Usually it is the same as a ROMEX® connector. If so, just remove the wire and connect the ROMEX® to the light.
    Last edited by Terry; 12-07-2011 at 10:21 AM.

  7. #7

    Default

    Another option you have is they make "clock outlets". They look like this...
    http://ecx.images-amazon.com/images/...500_AA280_.jpg

    These are for installing electric clocks on a wall so the clock will sit flush to the wall.

    This would allow the plug to recess a bit giving more room in the cabinet. (Need a deep box for this.) I don't know if they sell these at box stores like "Home Deplete Your Bank Account". Might need to go to an electrical supply house.

    Then also you can shorten the plug-wire going to the fixture, then you would not have that coil of wire in the cabinet.

  8. #8
    DIY Member edlentz's Avatar
    Join Date
    May 2008
    Location
    Michigan
    Posts
    70

    Default

    I hadn't thought of the clock recept. Good idea!

    Here's what I have

    http://zilotek.com/led_striplight.htm

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •