(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 10 of 10

Thread: Spray Foam Insulation Kits

Hybrid View

  1. #1

    Default Spray Foam Insulation Kits

    Anyone used one of these kits?
    http://www.fomofoam.com/

    Great R-Value. What are the downsides?

  2. #2
    Homeowner geniescience's Avatar
    Join Date
    Nov 2005
    Location
    humid summers hot, humid winters cold
    Posts
    2,152

    Default

    it'll replace batts in residential one day. Already is standard in commercial and industrial.

    can be hard to work with. Rigid foam panels are easier to install.

    david

  3. #3
    Engineer Furd's Avatar
    Join Date
    Jul 2007
    Location
    Wet side of Washington State
    Posts
    446

    Default

    Downside is that it is expensive. It also takes a bit of getting used to just how much to spray to fill the cavity without it expanding far too much. I think I got about three feet by eight feet of 2X4 wall cavity out of a $100.00 kit.

    Also, you have about 20 seconds from the time you stop spraying until you have to start spraying again or the tip needs to be changed.

    Plus you have to be able to get rid of the empty tanks. Most garbage haulers will balk at taking pressurized tanks. I had to cut my tanks in two to get rid of them.
    Last edited by Furd; 09-10-2007 at 09:06 PM.

  4. #4

    Default

    Whoah,

    I wondered how working with this stuff might be. Wow never would have guessed that expensive and difficult. By the sounds of it, must be a two man job.

    Anyone else have first hand experience with this stuff?

    Tom

  5. #5

    Default

    I used two of the $300 kits to insulate between the floor trusses in my basement where I could not access to fit foam board. It worked out really well. The only down side is of course the cost.

    Like was posted above, you need to work fast so the nozzle doesn't plug up.

  6. #6
    DIY Member Bosun's Avatar
    Join Date
    Jan 2005
    Location
    Minneapolis
    Posts
    89

    Default Pro-job

    Hire a pro to do it. It is no fun to clean up that stuff when you overspray, etc...

    Or do rigid foam yourself. I just did XPS in my 1924 basement. Glued it to the walls using lots of polyurethane glue. Lots. Much cheaper. Took my brother and me one day. Taped the seams with foil tape. No fiberglass batts.

  7. #7
    DIY Senior Member molo's Avatar
    Join Date
    Sep 2006
    Location
    cold new york
    Posts
    840

    Default

    These products, along with so many others in the building industry come with so many health warnings that it's scary.
    The following question is not sarcasm, it is an honest inquiry; Regarding human health, I'm wondering if to be in the building trades, you have to resign yourself to the increased possibility of death caused by the materials you work with. (we're all going to die, it's just a question of how).
    Regarding human and the planet's health, I'm wondering if we believe that through technology we will be able to clean up the environment when it gets to the point that the vast majority of people accept that it has become unhealthy to live in, or rather than cleaning it up, are going to abandon it and take up residency on other planets? I am very concerned about our water source, as you p[lumbers know things don't "disappear" when they go down the drain"

    These are serious questions that I have for the other folks on this forum. I am interested in some individual responses.
    Last edited by molo; 09-11-2007 at 06:53 AM.
    "Any American who is prepared to run for President should automatically, by definition, be disqualified from ever doing so."
    Gore Vidal.

  8. #8

    Default

    Interesting topic. I think one day water will be the most valuable resource available even though there is an abundance of it.

    Tom

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •