(206) 949-5683, Top Rated Plumber, Seattle
Results 1 to 9 of 9

Thread: double sink: one trap or two traps?

Hybrid View

  1. #1
    DIY Member adrianmariano's Avatar
    Join Date
    Jan 2007
    Location
    Massachusetts
    Posts
    79

    Default double sink: one trap or two traps?

    I'm replacing my kitchen sink. The existing sink is a double sink installed with two traps. Each sink has its own trap (1.5") and the pipes then meet in a wye. But when I was looking at a plumbing book I saw they had illustrated a double sink where the garbage disposal waste line (1.25" pipe) traveled horizontally to the other sink's waste line above the trap and then there was only one trap (1.5").

    Which arrangement is better? Does it matter?

  2. #2
    Forum Admin, Expert Plumber Terry's Avatar
    Join Date
    Aug 2004
    Location
    Bothell, Washington
    Posts
    14,191
    Blog Entries
    1

    Default

    You are only allowed one p-trap on a trap arm.

  3. #3
    DIY Member adrianmariano's Avatar
    Join Date
    Jan 2007
    Location
    Massachusetts
    Posts
    79

    Default

    I'm not sure I know what exactly "trap arm" means. Does the trap arm extend all the way back to the vented pipe?

    My existing drainage has a vertical cast iron drain pipe that is (presumably) vented. The drain for the kitchen sink comes off of that cast iron pipe in the basement, runs vertically through the floor, then it turns 90 degrees and goes about a foot horizontally, then it splits into two pipes and each of those two pipes has a trap on it before connecting to the sink or disposal.

    So is my existing plumbing in violation?

  4. #4

    Default

    i just did the same as you i have a disposal with a horizontal to a "T" that goes down into an Strap/Ptrap that goes into the floor/wall just put the trap below the T and you're fine but you dont need 2 traps. You remove the Y or cap one end and connect everything to the other side.
    Last edited by drocket; 01-16-2007 at 02:00 PM.

  5. #5

    Default

    One trap only...that's it.

  6. #6
    Moderator & Master Plumber hj's Avatar
    Join Date
    Aug 2004
    Location
    Cave Creek, Arizona
    Posts
    25,615

    Default traps

    Two traps are a solution to a specific problem and are normally only used when the pipe from the wall is too high for the one trap installation. Many inspectors will reject an installation with two traps connected to one opening.

Similar Threads

  1. Double basin laundry sink -- how many traps?
    By DavidTu in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 2
    Last Post: 06-12-2012, 06:39 AM
  2. Converting to double sink-drain pipe too close to stud for double fixture fitting.
    By Finch85 in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 8
    Last Post: 04-11-2012, 06:04 PM
  3. Double Sink double dishwasher garbage disposal dilemma
    By Pettytalk in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 3
    Last Post: 01-12-2012, 05:04 AM
  4. Why do sink traps leak?
    By tilelayher in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 0
    Last Post: 10-02-2010, 09:29 AM
  5. Kitchen double sink mildew, need 2 traps?
    By dwc2mn in forum Plumbing Forum, Professional & DIY Advice, Tips & Tricks
    Replies: 1
    Last Post: 05-31-2008, 06:40 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •