(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: eric3872; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.19 seconds.

  1. Replies
    3
    Views
    391

    Thanks for the reply. I haven't gotten around to...

    Thanks for the reply. I haven't gotten around to doing this yet. The existing supply is actually 1" PEX. Not sure what you mean by connect them as a single run. The supply is from the floor above,...
  2. Replies
    15
    Views
    2,037

    Ok... Here's my plan B. I've revised the...

    Ok... Here's my plan B. I've revised the diagram. I'll have to spend some more time demoing the ceiling but I've got an extra slot I can use, so I'm going to use two circuits. I'll run 2 wire...
  3. Replies
    15
    Views
    2,037

    Right now there are two lights on the same...

    Right now there are two lights on the same circuit. They are controlled by two separate single pole switches. I want to put them both on three ways and be able to control them independently. It...
  4. Replies
    15
    Views
    2,037

    I understand. I'm going to run the power through...

    I understand. I'm going to run the power through the power through the switches. I've decided to split this up into two circuits and will follow your advise from post three.
  5. Replies
    15
    Views
    2,037

    Thanks for the info. I've got two sets of these...

    Thanks for the info. I've got two sets of these lutron 3 way dimmers. They are a master and slave configuration. I guess I assumed if each set was controlling a separate fixture, they wouldn't...
  6. Replies
    15
    Views
    2,037

    Thanks for the responses. Any thoughts on how to...

    Thanks for the responses. Any thoughts on how to simplify this? I've thought about running the power to the switch first rather than the fixture but that will involve longer runs and a lot more...
  7. Replies
    15
    Views
    2,037

    Please Critique My Wiring Diagram

    I am about to start rewiring the lighting in my kitchen. Right now I've got four lights on one circuit controlled by two separate single pole switches (two sets of two lights, each with a separate...
  8. Replies
    3
    Views
    391

    Fin tube Installation Help

    I am replacing a single tube hot water baseboard with a two tier unit unit in my kitchen. The supply comes from above on the right side and the return is on the left going down to the floor below. ...
  9. Replies
    8
    Views
    2,280

    Thanks Cacher Chick. I am planning on replacing...

    Thanks Cacher Chick. I am planning on replacing the 14/2 with 12ga wire. So, you are saying I cannot have two sets of 3way switches on a single feed from the 20amp circuit? I'd need to run them...
  10. Replies
    8
    Views
    2,280

    I have some 12/3 MC cable laying around, but I...

    I have some 12/3 MC cable laying around, but I might buy some new NM for ease of installation.
  11. Replies
    8
    Views
    2,280

    Currently the 4 fixtures are wired with 14/2 BX...

    Currently the 4 fixtures are wired with 14/2 BX from a 20amp breaker with the single pole switch at the end of the run. I will rewire if necessary back to the breaker box, but I'd like to use the...
  12. Replies
    8
    Views
    2,280

    Help with wiring diagram

    I'm hoping someone can help me with a wiring diagram or some input on a rewiring project I'm doing in my kitchen.

    I have two sets of fixtures that are on a single circuit and controlled by a...
  13. Replies
    21
    Views
    3,970

    They are being completely removed. They feed...

    They are being completely removed. They feed outlets that are not being used. There are at least 4 dedicated circuits on this panel that feed outlets for window air conditioners. The previous owner...
  14. Replies
    21
    Views
    3,970

    The main feed wires are definitely larger than...

    The main feed wires are definitely larger than #10. They are not labeled, so I can't tell what gauge, but they are at least twice the thickness of everything else in the panel.
  15. Replies
    21
    Views
    3,970

    There does not appear to be a separate ground...

    There does not appear to be a separate ground connection to either bus.
  16. Replies
    21
    Views
    3,970

    I am removing two of the tandem circuits to make...

    I am removing two of the tandem circuits to make room for the 30 amp breaker. So there will not be any additional load added to the panel.
  17. Replies
    21
    Views
    3,970

    This is a sub panel I believe. It's a...

    This is a sub panel I believe. It's a multi-family house There are three electric meters with main panels in the basement for each apartment. This one is located in the apartment. Believe it or...
  18. Replies
    21
    Views
    3,970

    I see. Here they are: ...

    I see. Here they are:

    http://i1212.photobucket.com/albums/cc453/eric3872/photo3.jpg

    http://i1212.photobucket.com/albums/cc453/eric3872/photo2.jpg
  19. Replies
    21
    Views
    3,970

    Here are the photos. Didn't realize I couldn't...

    Here are the photos. Didn't realize I couldn't upload from my pc.

    http://s1212.photobucket.com/albums/cc453/eric3872/
  20. Replies
    21
    Views
    3,970

    Grounding Bus Questions

    You have all been really helpful with your advice and suggestions. I'm wiring a new clothes dryer and am at the final step. I've run into a snag. I ran 10/3 from a new 30amp outlet. I have a...
  21. Replies
    17
    Views
    5,932

    Not sure I understand what you're suggesting. ...

    Not sure I understand what you're suggesting. This breaker is 1". It will only take one slot. Are you saying I could replace one of my single pole 15amp breaker with this one and combine the...
  22. Replies
    17
    Views
    5,932

    Thanks. So, Is there such a thing as a 2P 30amp...

    Thanks. So, Is there such a thing as a 2P 30amp breaker that's only 1"?
  23. Replies
    17
    Views
    5,932

    Circuit Breaker Question

    I need to add a 30 amp breaker to my panel for a clothes dryer. I understand that I need a 2P 120/240 breaker. The problem is that I only have a 1" slot available.

    My panel is a cutler Hammer. I...
  24. Replies
    2
    Views
    1,348

    New Washer Hookup

    I have a plumber doing various minor upgrades in my house. We are about to start on the largest part of the work (running piping for a new washing machine). The washer will be located in a room...
  25. Replies
    20
    Views
    4,496

    clarification

    The panel is full and space is needed to add the new 30 Amp breaker. The dedicated circuit for the 220 outlet is was added for an air conditioner, but is in a location where no AC is needed (laundry...
Results 1 to 25 of 28
Page 1 of 2 1 2