Search:

Sure, mount them to the 2x4 drop panel with holler wall anchors or toggle bolts. You now can buy smoke detectors cheap so I would use 3 in the room. One on each side in the middle and one above the...

Can let you know. I am installing one in the job we are working on now and have the info on the job site. This unit has a metal frame that mounts into the stud bay, (2x6 wall). I just reframed the...

That's strange, just installed one yesterday. First one I seen. I don't know if I like this or not. To many little wires hanging under the sink. The green ground wire had little wire hooks to go...

Yea tile job messed up to start with. I always run my tile down to the outlet mounting screw so the outlet will lay on top of the tile. In this case I would cut a small piece of tile to slip up under...

Had the same problem in a house a few months back. Installed a new vinyl window and used 1x4x 3/4 PVC trim to trim it out. Tiled up to it and ran a bead of good silicon around the trim.

To me the inside of the pex seems to work fine but it's the very small dia of the 90 brass pex fitting that causes the restriction. I run pex up to the showerhead and this works fine to me.

Now just a guess here but maybe with the air on and the house colder it is cooling down the water lines and causing the water heater to come on more. Just a guess.

One question was not touched on. What about kerosene in the heating unit?

Sounds to me with the water level in the bowl dropping like it is that may also, along with a sometimes clog, be a clogged vent somewhere so as water is draining from say a tub or sink it is pulling...

Question, with the duct work behind the sink I take it that the drain and water supply is coming up through the floor? There is a thread here about installing a pedestal sink that has the drain...

What kind of drain stopper do you have. This could out of adjustment and cause a slow drain.

Yes that would be one heck of a leak and for some time too.

Just seen Redwood's post to another topic here and if I may, does it look like this.............

http://www.deltafaucet.com/media/Product_Tech_Docs/Parts_Diagram/Models_622_635_636_641_642_5985.pdf

Maybe Southrenman should have said two of them are them same "width" as a 2x4. 1 3/4 X 2 + 3 1/2.

I take it that the sleeve slides through the face plate and the leak was between the two? Most of the time there is a foam gasket on the face plate that seals against the sleeve. You might try to put...

Will have to check into this Ditra. Here alot about it here.

After installing many of them over the years, and I might add in kind of shady neighborhoods, I have found if you take two 2 1/2" screws and counter sink the into the edge of the door jamb about 1/2"...

No vapor barrier. I allways set the backer board in thinset so you can't use a VB. If I have to tear up the floor first then I put 30pd felt paper between the two layers or plywood.

Why are you having to comply with your plumber? I thought the homeowner was in charge? All my clients are the boss! To me I would keep the old toilet and install the mixing value. You should have a...

Just did a kitchen/living room floor over the 4th. I used a scrap of the flooring to use as a spacer. little over 1/4". If you leave 1/2" it will be close for the shoemold to cover. If you use full...

Yea I overlooked it! :o

The page I have bookmarked shows all the different forums. Is there a link to a page that shows just the new post each day? Thanks and what a great and info site this is.

I would go with pex. Your layout sounds good to me.

I would think the disposal, of coarse mounted to the sink, will have a inlet for the dishwasher at the top side. Now is your drain in the wall or through the floor? P trap to this I would think.

Are there enough vents here? When you flush the toilet would it not suck water out of the p trap in the bath sink?