(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: kordts; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Thread: Brazing

    by kordts
    Replies
    6
    Views
    1,231

    Unless it's under a slab it doesn't need to be....

    Unless it's under a slab it doesn't need to be. Brazing rod is much more expensive than 95/5 or lead free solder. Also it's real easy to blow a hole thru 1/2" or 3/4" with oxy-acetylene. Brazing is...
  2. Replies
    10
    Views
    1,229

    You need a new 3/4" full port female NPT ball...

    You need a new 3/4" full port female NPT ball valve.
  3. Thread: For Plumbers:

    by kordts
    Replies
    7
    Views
    1,221

    I wonder what state Megan Lehtonen is a licensed...

    I wonder what state Megan Lehtonen is a licensed plumber in. What a joke, it makes ashamed to be a UA member, pushing this crap.
  4. Replies
    22
    Views
    4,515

    "At the time the country was run by a cowboy and...

    "At the time the country was run by a cowboy and was full of cowboys. Freedom eh? Yeah, to rip people off."

    So now our country is run by a socialist and is full of socialists. Freedom, eh? No,...
  5. What depth did the rough in instructions specify?...

    What depth did the rough in instructions specify? Have the plumber come back and rough it in where it is supposed to go. Then backcharge him to pay for the tile guy.
  6. Replies
    15
    Views
    2,101

    Yes, putting paper towels under the joints and...

    Yes, putting paper towels under the joints and then lifting the pipe out of the ditch is the approved method.
  7. Replies
    6
    Views
    840

    Good luck with that galvanised to the tub...

    Good luck with that galvanised to the tub spout.:eek:
  8. Replies
    4
    Views
    11,229

    There is a company that makes bases that seal on...

    There is a company that makes bases that seal on the flange, then the toilet seals on the base. You can get to 18" that way.
  9. Replies
    37
    Views
    4,137

    Did you put proper pitch or supports on your...

    Did you put proper pitch or supports on your pipes? Did you make a "s" or a "p" trap? Long sweeps for change of direction? 6" above floodrim before the vents go horizontal? Proper size of pipe per...
  10. Replies
    37
    Views
    4,137

    Having a neighbor do your floor and smockmen tell...

    Having a neighbor do your floor and smockmen tell you how kooh up pipes isn't the same as inspection.
  11. Replies
    6
    Views
    1,412

    Was it an installation leak, like a bad solder...

    Was it an installation leak, like a bad solder joint? Or was it defective material? If you supplied all the material, the plumber got no markup to pay for any callbacks. You lose.
  12. Why didn't you plumb that 2" into the box?

    Why didn't you plumb that 2" into the box?
  13. Replies
    12
    Views
    1,321

    glad to have helped.:D

    glad to have helped.:D
  14. Replies
    6
    Views
    2,271

    I have had vapor lock, but never in plumbing...

    I have had vapor lock, but never in plumbing situations.
  15. Replies
    4
    Views
    2,007

    Should have sent in the Ohio National Guard in at...

    Should have sent in the Ohio National Guard in at Woodstock and rousted those hippies.
  16. Replies
    118
    Views
    24,341

    I just threw up a little in my mouth.

    I just threw up a little in my mouth.
  17. Replies
    11
    Views
    2,819

    I hate to get involved with this, but I am...

    I hate to get involved with this, but I am compelled to say, why does the drain have to go on center? If it's a custom shower, the drain can go anywhere.
  18. Replies
    5
    Views
    781

    Lav or kitchen? Stainless or cast?

    Lav or kitchen? Stainless or cast?
  19. Replies
    9
    Views
    1,708

    Please don't do this. It is such a hack way of...

    Please don't do this. It is such a hack way of doing things. Can't you install a dual outlet angle supply stop under your kitchen sink? A better way is to solder a tee in the cold riser under your...
  20. Replies
    12
    Views
    4,835

    "To the rest: First, I am a retired telephone...

    "To the rest:
    First, I am a retired telephone installer - so keep your attitude and discrimination towards others you perceive to be different from you (ie: perhaps having more money or being a...
  21. Replies
    12
    Views
    4,835

    Wow, what a nerve, coming on to a plumbing...

    Wow,
    what a nerve, coming on to a plumbing website, getting free advice, and then ripping on plumbers. I really hope you paid a lot of money for those junk faucets.
  22. Thread: sweating theory

    by kordts
    Replies
    12
    Views
    1,352

    I would have installed the nipple between the...

    I would have installed the nipple between the valves first, then anchored the valves. You put the cart before the horse.
  23. Replies
    11
    Views
    1,579

    If ya don't mind getting wet, shut off that...

    If ya don't mind getting wet, shut off that valve, cut the pipe coming out of the top. Get a new threaded 3/4" ball valve and put pipe dope on the threads and open it. Spin the old valve off, spin...
  24. Replies
    8
    Views
    1,018

    For sweat, I use full port, so I can get...

    For sweat, I use full port, so I can get Jet-Swets into the line if needed.
  25. Replies
    14
    Views
    2,901

    You sure dig teddy bears, don't you? I think this...

    You sure dig teddy bears, don't you? I think this is the wrong site for ya.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4