(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: adenwork2; Keyword(s):

Search: Search took 0.12 seconds.

  1. The ARRA and BAA include many countries other...

    The ARRA and BAA include many countries other than the USA.

    "designated countries qualify as a part of the recovery package. These countries include: World Trade Organization Government...
  2. Quality did go down. Fit and finish and other...

    Quality did go down. Fit and finish and other non cosmetic problems were worse in my newer N.A. built Honda than an old Honda. The new one had the usual routine transmission failure far far below...
  3. Replies
    6
    Views
    2,621

    Non plumber here with an Aquia II and new flange...

    Non plumber here with an Aquia II and new flange installed by a licensed bonded plumber. Unfortunately, the newly installed flange of regular painted steel [not stainless] is on the wood floor, below...
  4. Replies
    7
    Views
    1,934

    Some measurements on a Supreme round front not Eco

    My not eco Supreme round front is 21 7/8 inches high at the tank from the floor with cover removed. Water in tank is 2 1/4 to 2 3/8 from the top with cover removed. Not exact measurement. The...
  5. Fleck 5600 What goes wrong with age? Why is the large knob hard to turn?

    My Fleck 5600 Economider is over 20 years old.
    Every 2 years or so, the large knob on the front is hard to turn. ...
  6. Replies
    2
    Views
    933

    Have Aquia II, Vespin, Supreme (made in Vietnam)....

    Have Aquia II, Vespin, Supreme (made in Vietnam). No Drake.
    Water spot of Aquia II is smallest. Compared to Vespin and Supreme, stool can more easily hit bowl above water spot to make streak more...
  7. Replies
    3
    Views
    1,273

    Notes on things not in any specifications.

    I have an Aquia II, Vespin and Supreme. I find the Aquia II easier to clean on the outside from skirt design. The inside of the bowl gets streaks (streaks of stool) because the water spot is very...
  8. Replies
    4
    Views
    764

    I found the Carusoe somewhat splashy. Splash out...

    I found the Carusoe somewhat splashy. Splash out of toilet when flushing. Builder installed in a new house when I was visiting. Don't know if has changed since then.
  9. Replies
    31
    Views
    9,655

    Yes. Those are the exact part numbers for the...

    Yes.
    Those are the exact part numbers for the AS Cadet 3 RF 10" number 2384010 in the catalog. Nominal dimensions 26-1/4" x17-1/4" x28-7/8". See the link for the spec sheet. ...
  10. Shower question, Delta T18 series, good or not?

    A question about a shower valve for a remodel. I will be hiring a contractor for all work. The agreed price includes $400 for a shower valve, $350 for each sink faucet, $400 for each toilet. ...
  11. Replies
    11
    Views
    1,488

    I would rather get Toto, but due to lack of space...

    I would rather get Toto, but due to lack of space and 10" rough in, I might have to get one Cadet 3 RF.

    What kind of defects would you look for if you had to get an American Std.? Is it just...
  12. Replies
    1
    Views
    11,925

    What 10" rough in to get?

    I need 3 good performing 10" rough toilets for a remodel. What toilet to get?

    I have several questions and issues.
    10" rough in.
    Wall to front of bowl dimension.
    Water supply 5-6 inches from...
  13. Replies
    5
    Views
    1,538

    Might want to try before buying. I found the CST...

    Might want to try before buying. I found the CST 703 splashy. Similar to CST 704. Flushes well, splashes out of the bowl when flushing.
  14. Replies
    0
    Views
    468

    Razor in toilet

    Just finished removing a razor from a toilet. Loads of fun. Plastic disposable but had a larger than usual handle. Someone admitted dropping a razor so at least I had an idea what the problem was....
  15. Replies
    6
    Views
    1,573

    Flush is strong, not as strong as Drake. However...

    Flush is strong, not as strong as Drake. However CST703 splashes out of the bowl on to the floor when flushing more than most toilets. I don't like splashing.
  16. Water Hammer when Clothes Washer shuts off water

    I have had a water hammer problem for about a year. This started after I had to replace one hose bibb and one water hose to the clothes washer. The hot water hose was fused to the hose bibb. I...
  17. Replies
    6
    Views
    1,650

    Fluidmaster: I have had the rubber washer inside...

    Fluidmaster: I have had the rubber washer inside the black plastic cap at the top of the valve fail at times. Easy to replace. I do have Chloramines in water.
  18. Replies
    9
    Views
    4,707

    10" rough in. I bought a Cadet round front bowl...

    10" rough in.
    I bought a Cadet round front bowl 3454.016 with a Compact tank, part number not known. This did have a 10" rough in. Not a super performer. It is adequate and I could not wait for...
  19. Replies
    9
    Views
    4,707

    Is the CST 704 splashy?

    Did the CST 704.10B cost anywhere near the list price? I hope not.
    I found that the CST 703 is rather splashy from the bowl when flushing. Do you notice this?
  20. To improve the flush, make sure the tank water...

    To improve the flush, make sure the tank water level is the highest possible.
    Change to a generic flapper or adjust the float on the flapper chain so that the flapper opens longer. Or hold the...
  21. Replies
    54
    Views
    141,025

    Get brass outer part of cartridge out?

    I hope you have already solved the problem. Years ago, I had the same issue. I had to call Moen and get a live person to help. I found that I had to first put a small wood dowel in. It was just...
Results 1 to 21 of 21