(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: nottick; Keyword(s):

Search: Search took 0.11 seconds.

  1. Replies
    1
    Views
    801

    Kohler Wellworth Model 11471

    Hello and again I will say thanks in advance to any and all that can provide assistance.

    Removed an American Standard bowl, back of tank was dead 12 inches from the back of tank to the center of...
  2. Replies
    6
    Views
    3,441

    HJ, replaced what was broken

    As is the case with most of the posts I do here, I tend to inherit the problems after a staff member has screwed-up.

    After some questioning of the individuals involved I was able to learn that the...
  3. Replies
    6
    Views
    3,441

    GE Water heater

    Being as the top access panel is where I had the spark, can I assume the top element and thermostat are the only things that need to be replaced?
  4. Replies
    6
    Views
    3,441

    Problems with GE Hot Water Heater

    A GE water heater( 30 gallon) manufactured by Rheem was installed.

    It was powered "on" before it was fully filled.
    It made hot water the first day, the second day I had to press "reset" button....
  5. Replies
    23
    Views
    19,917

    Install dusk to dawn sensor ( Epiloque and a THANKS to all who assisted)

    1- Please accept apologies if I don't communicate well as English is not my first language.

    2- This issue was resolved as such; I installed a new switch ( from inventory), still had same problem....
  6. Replies
    23
    Views
    19,917

    Hillbilly

    My feed comes up the pole. ( lamppost).
    The flagpole light wires come from the fixture up the pole.

    I have correctly identified which is which.

    I also tried this ; installed sensor to just...
  7. Replies
    23
    Views
    19,917

    WV Hillbilly

    I tried both . Each time the first light remained "on"
  8. Replies
    23
    Views
    19,917

    Codeone

    "So in this lamp post you have two conductors coming from the house a hot and a neutral going up the pole to the sensor"

    As of right now I do not have a sensor installed, but yes, I have a hot and...
  9. Replies
    23
    Views
    19,917

    Codeone

    The sensor is mounted on the pole of the first fixture.( the first fixture is an exterior garden lamppost) of the first fixture. The first fixture is the one that remains "on".

    This feeds the...
  10. Replies
    23
    Views
    19,917

    Response to codeone

    Codeone,

    From the breaker the service goes directly to a fixture. and then to the second fixture ( which is about two feet away).

    There was an existing sensor which controlled both fixtures....
  11. Replies
    23
    Views
    19,917

    Thank you for the reply. You said "The feed...

    Thank you for the reply.
    You said
    "The feed is the 120V power. it goes to the black wire of the photo cell (which you refer to as the switch)

    The red wire goes to the black wire(s) going to...
  12. Replies
    23
    Views
    19,917

    Dusk til dawn switch( sensor)

    I understand that -

    Red - to black wire of fixtures.

    Did this ,but one remains on all thevtime
  13. Replies
    23
    Views
    19,917

    Installing a dusk til dawn sensor

    Hello ~
    I am having a huge headache with a dusk til dawn sensor switch.

    The switch has three wires, red black and white.

    It has to service two seperate light fixtures.

    I have tied the feed...
  14. Thanks Fellows

    My installation took place without any problems. Of course figuring out how to program the timer was another story - but the installation went well.. Again I owe thanks to this forum for the...
  15. Wiring Solenoid Valves for Sprinkler Manifold

    Hello. I have my manifold built, valves installed. Control mounted, etc.
    All I have to do now is figure out how to wire the valves to the five wires( I used a five wire jacket - four zones and...
  16. Replies
    10
    Views
    1,440

    Yes, and they are sold /marketed as "pre-tinned"....

    Yes, and they are sold /marketed as "pre-tinned".

    That is why I used the subject " Pre-tinned Fittings".

    On the boxes which they are shipped by manufacturer there is a label that says "...
  17. Replies
    10
    Views
    1,440

    I am seeking information about fittings that are...

    I am seeking information about fittings that are sold pre-tinned, not fittings that have been soldered and then removed.

    Unless your "search" results are tricking me, I don't see that "discussion".
  18. Replies
    10
    Views
    1,440

    Pre-tinned Fittings

    Anybody have any input as to pre-tinned fittings? I have seen them in the big box shops, as well as plumbing supply houses.

    They are considerably expensive on a percentage basis as compared to the...
  19. Replies
    14
    Views
    1,841

    It cuts out = hot water cuts out. For a few...

    It cuts out = hot water cuts out. For a few minutes cold water will flow, then the hot water returns.

    Hopefully new tubes will do the trick.

    QUOTE=geniescience]You said it cuts out. The hot...
  20. Replies
    14
    Views
    1,841

    Reply to BOb NH

    I do not have a tempering valve. THe problem exists throughout the entire house.

    Thanks for the response. Now all I have to do is hope that Sears Parts dept has the tub for an 18 yr old unit!!!!
  21. Replies
    14
    Views
    1,841

    Water Heater Problem ( New Forum Member)

    Have a Kenmore Power Miser, ( it is almost 18 years old :eek: ), electric , not gas powered.

    Hot water just cuts out and then returns randomly. Sometimes the hot water will cut out after 5...
Results 1 to 21 of 21