Search:

Gregsauls,
It's a model R53.

I know what you mean, I think it's intimidation and insecurity. If it can't be fixed with a pipe wrench, they are lost. Any new technology, anything from the...

All,
I would like to tell you about my limited tankless heater experience. About a year ago I purchased and installed a Rinnai tankless water heater for my lake home in northern Minnesota. The...

I will not be hooking up the line until spring. Thanks everyone for the advise

nhmaster,
Yes, I have the proper equipment and training, and I do have a univeral license. The reason I ask is because I usually work on environmental chamber and not residential system and was...

All
I purchased a cased ac A coil for my furnace and would like to install it with out installing the condensor. The instructions say that it is pressure charged and the pressure should be released...

I have installed a sewage ejector pump to lift the waste form the lower level bathroom to the pipe going out to the septic tank. when the pump shuts off the pipes bang and shake, its louder than I...

Jad, MPM,
thanks for your reply.
The tankless heater came from the factory setup for propane use only, and in the literature and on a label at the connection it says to use a 3/4" supply. The gas...

I'm installing a Rinnia tankless water heater that will operate on propane. I'm confused about the size of the gas line. The manufacturer requires a 3/4" line to the heater (up to 180,000 btu). I...

In most houses where I live (Minnesota), cold water faucets in the kitchen sink are plumbed with unsoftened water. Some say it is that way because the hard water tastes better, and I suppose the...

All,
thanks for the reply's
I just wanted to make sure they trip before the inspection, for the GFCI's I used a plug in device to check that the wiring is correct, and it has a button to trip the...

Hello all,
I have my final electrical inspection this week and was wondering if there is a way to test arc fault circuts, other than using the test button? I've heard that the devices on the market...

thanks everyone for your help.

thanks Frenchie

the box I used must be ok because I have already had my rough in signed off, can you give me an example of an approved box and cover.
Thanks

If outlets are installed in the floor, do you need a mud ring to bring the outlet up to finished floor level. Also, do you need a covered switch plate like the ones you use for outdoor outlets?...

Can it be a 15 Amp GFI?

Thanks for the reply. I did not know it was allowable to use 15 amp recepticles on a 20 amp appliance circuit.
Thanks again

ALL
I have installed my 2 - 20 amp appliance circuits, and I am ready to install my recepticles. The only 20 amp recepticles that I have been able to find have one of the blade slots at 90 degrees...

Thanks all for your input, The reason I'm asking is because may sewage pit is in the center of the basement level, and I have a 1st with a loft above that. no central walls in the loft to run a pipe...

Hello All
does the 2" vent for a sewage ejector pit have to be a separate vent all the way to the roof, or can it connect to the main vent?
thanks in advance for your help

I have a couple of question that I'm hoping someone can answer, any response will be greatly appreciated.
1. It states in the code book that type nm ROMEX® run thru floors is to be protected by...

I have 2 12/2 MN ROMEX® running to a well pressure tank switch from the panel. above the pressure tank the ROMEX® is stripped and I have the 4 current carrying conductor and 2 grounds running in 1/2"...

What is the maximum distance a vent can run horizontally from the main vent stack. I have a kitchen sink vent and a washer stand pipe that are both about 25 feet away from the main vent stack. I'm...

Can I use 10-2/W GND romex to run power to a central A/C condenser if I mark the white wire? the unit is 220VAC at about 20 amps.
Thanks

Thanks for the information, what about the pig tailing of recepticles and switches?