(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: raybigto; Keyword(s):

Search: Search took 0.13 seconds.

  1. Replies
    2
    Views
    897

    Awesome!! Thank you so much Rugged. :)

    Awesome!! Thank you so much Rugged. :)
  2. Replies
    2
    Views
    897

    TOTO Doesn't Fill After Flushing

    Hi All,

    I installed a TOTO toilet 1 year ago and it has been great until recently it doesn't fill after flushing. Often I have to life the lid and pust the "blue thing" until it reacts and starts...
  3. Replies
    13
    Views
    2,580

    after cut

    I just finished cutting the cast iron w/ reciprical masonary blade and wax and the two vents w/ circular masonary blade. I have to say that the circular saw was much easier. I used some rope to...
  4. Replies
    13
    Views
    2,580

    Thanks Cass, just finished cutting point 2, I'll...

    Thanks Cass, just finished cutting point 2, I'll keep updates for anyone who's following. Just realized that the slanted tub vent will block the way for the new tub. The old one had a gap that hid...
  5. Replies
    32
    Views
    7,842

    Dead doctor

    That's scary. To be rich and dead.

    I had Lasik 7 years ago and I still sometimes push my invisible glasses up. Sometime my eyes tear up and sting, but I'm not sure if that's from lasik or...
  6. Replies
    13
    Views
    2,580

    Tub p-trap question

    http://www.terrylove.com/images/abs/nohub.jpg

    If I started ABS from point 2, is the p-trap done the same way as the sink with a slip nut? Otherwise I would have to VERY precise with the plastic...
  7. Replies
    13
    Views
    2,580

    Got it out!

    With some heat I got the bronze pipe out. It was actually taped with masking tape and plummer puttied! Wow.... I cleaned out the threads with a wire brush and can got about normally. Just in...
  8. Replies
    6
    Views
    2,661

    "t"

    for those following, I've decided to remove the T and replace with ABS and connect to the Vent above and Cast Iron below. Then attach a marvel fitting... Thanks all for your help.. I probably...
  9. Replies
    6
    Views
    2,661

    Thanks!

    I posted a diagram at my other post. Both the sink drain and bathtub drain tie in and connect to a main 2"... Thanks for all your comments. Here's the link...
    ...
  10. Replies
    13
    Views
    2,580

    Cut close up

    Here's a close up of the planned cut location #2.... Last check before it's a done deal <deep breath>.
  11. Replies
    13
    Views
    2,580

    Thanks!

    Thanks for the replies guys. I drew up a diagram showing different points I'm considering cutting. It seems cutting at location 2, 3 and 4 would allow me to fill in with PVC (banded coupling at...
  12. Replies
    6
    Views
    2,661

    Chrome Drain Pipe to Cast Iron

    In redoing our bathroom, I found a chrome 1.5" pipe connected to cast iron. Is there a fitting out there to connect the chrome to pvc? Or is it best for me to remove the chrome piece? The chrome...
  13. Replies
    13
    Views
    2,580

    Another angle (photo)

    Here's another photo with a different angle.... Hope I don't have to redo the cast iron section.
  14. Replies
    13
    Views
    2,580

    Glued Pipe to Cast Iron?

    Hi Everyone,

    This will be my first post here. This forum is awesome. Here goes.... In removing the old tub at home, I found the tub drain connection "glued" to the p-trap. The photo shows the...
Results 1 to 14 of 14