(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: Rickcusaf; Keyword(s):

Search: Search took 0.11 seconds.

  1. Replies
    17
    Views
    2,258

    I appreciate it. The model number starts with...

    I appreciate it. The model number starts with RGDG.

    Serial: DF5D302F069602895
  2. Replies
    17
    Views
    2,258

    It did, but there is no money for an HVAC guy...

    It did, but there is no money for an HVAC guy right now. They charge $75 an hour here with a minimum of one hour charged. It hasn't smelled like gas since though. When it happened the first time it...
  3. Replies
    17
    Views
    2,258

    Sorry for the delay in replying. The main board...

    Sorry for the delay in replying. The main board has three lights. The Power and Ok lights are on, but the Flame light isn't. Nothing flashes nor do I see any noticeable warning. I'd love to spring...
  4. Replies
    17
    Views
    2,258

    Would that cause the hot surface ignitor to not...

    Would that cause the hot surface ignitor to not glow though? Right now the ignitor is still not glowing.
  5. Replies
    17
    Views
    2,258

    Where would that be located so I can check it? I...

    Where would that be located so I can check it? I did some searching and only found stuff about Oil burners?
  6. Replies
    17
    Views
    2,258

    I ended up replacing the ignitor based on what a...

    I ended up replacing the ignitor based on what a local HVAC guy said. It still didn't glow, but when I turned it on this time, the gas started going and didn't shut off. I ended up turning off and...
  7. Replies
    17
    Views
    2,258

    Rheem 04EAUSR. Igniter doesn't glow.

    I have a Rheem 04EAUSR and when I turn it on and set it to call for heat, the unit starts up and blows air, but it's not hot. When I went to the garage to look at it, the flame wasn't on. I went...
  8. Replies
    7
    Views
    1,171

    Yup, I didn't know she had been flushing them...

    Yup, I didn't know she had been flushing them until she asked me if that might be the problem. Looks like it's not the drain. The grinder pump light turned on after my last post and my guess is some...
  9. Replies
    7
    Views
    1,171

    The water level stays the same in the drain. When...

    The water level stays the same in the drain. When the bowl is attached the water drains slowly from the bowl.
  10. Replies
    7
    Views
    1,171

    Toilet Clogged

    My fiance flushed a few tampons down the toilet and now the water drains incredibly slowly. I've tried using an Auger, Liquid Lightning, and pulled the toilet off to snake it from the back too. It...
  11. Replies
    6
    Views
    3,137

    Here are pictures of my current setup for my...

    Here are pictures of my current setup for my contactor. The wiring mirrors how my old setup was with the exception of the two wires on the side. The original setup had the brown wire on the top...
  12. Replies
    6
    Views
    3,137

    They were disconnected at the time, but I...

    They were disconnected at the time, but I connected them shortly after posting. Right now my biggest problem is that my gas furnace isn't turning on at all. I've used a multi-meter to check my wall...
  13. Replies
    6
    Views
    3,137

    Contactor replacement

    I had the HVAC guy come out to my place and he told me the contactor and capacitor needed to be replaced. He wrote down the parts I needed and I ordered them from a local appliance store. The new...
  14. I went to my local ace hardware and luckily they...

    I went to my local ace hardware and luckily they have a plumber on staff. I used my camera to take pictures of everything before I went and showed him my setup. Everything is working now.

    I cut...
  15. I've kept the water heater off the entire time....

    I've kept the water heater off the entire time. $220 an hour isn't cheap.
  16. I replaced the flex line and still have low water...

    I replaced the flex line and still have low water pressure. Any ideas?

    http://i43.tinypic.com/2mzb1nd.jpg
    http://i42.tinypic.com/2iht6ro.jpg
  17. I appreciated the help. I'm going to relocated my...

    I appreciated the help. I'm going to relocated my water valve off to the side so I have more room to work with since it's all kind of jammed in there and I'm going to run a flex line after that to...
  18. Right now cost is an issue and the cheapest...

    Right now cost is an issue and the cheapest plumber around wants $220 an hour plus materials. I'll replace the gas line with a new one and the fittings used are the ones that were the ones I had from...
  19. New GE 40 gallon. Low pressure over the entire house.

    I've been reading through and I think the culprit may be my water inlet line. The copper flex tube is kinked in two places, but I wanted to ask if anyone else had some ideas. I'm enclosing some...
Results 1 to 19 of 19