(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: mannerofspeakin; Keyword(s):

Search: Search took 0.13 seconds.

  1. Replies
    13
    Views
    2,375

    Ok, still not fixed. I ended up cutting the...

    Ok, still not fixed. I ended up cutting the valve out after trying to unsolder for too long. What I have left is one of the 90s completely off. Came off while unsoldering and the other side I have...
  2. Replies
    13
    Views
    2,375

    YEs water is off and drained. The only nut I see...

    YEs water is off and drained. The only nut I see is that pictured which only holds the handle itself on. The leak is coming from the body of the valve. You can see the leak to the left of the...
  3. Replies
    3
    Views
    1,748

    Thanks. It is 9 inches. Are there some ways to...

    Thanks. It is 9 inches. Are there some ways to convert current opening to something more common ? Like an adapter or something ?
  4. Replies
    13
    Views
    2,375

    Thanks. About how long with the torch should it...

    Thanks. About how long with the torch should it take to loosen the 90's sufficiently ? What type of torch do you recommend ? I am using a minibutane and it does not seem to be heating sufficiently.
  5. Replies
    3
    Views
    1,748

    Flexible insulated duct

    House built in 1990. Need to replace a run of flexible duct work. The ductwork that needs replacing has a "9'" stamped on it next to its manufacturer information on the outside, which should mean...
  6. Replies
    13
    Views
    2,375

    ball valve problems

    Ball valve is leaking from body of ball valve. It is soldered on to copper pipe. (See pictures attached). I think I need to cut the valve out and replace. The problem is if I cut out the valve...
  7. Replies
    4
    Views
    856

    Resurrecting an oldie but a goodie. Same model...

    Resurrecting an oldie but a goodie. Same model of Eljer here (same as picture at top of thread). The link given shows discontinued model pre-1993 and then the current model post 1993. Would the...
  8. Replies
    12
    Views
    5,091

    Tried the valve shut offs at all the various...

    Tried the valve shut offs at all the various outlets. No change. Could a low flow aerated shower head by causing the problem ? Maybe causing back pressure or something.
  9. Replies
    12
    Views
    5,091

    Actually I have done the first part. Water gets...

    Actually I have done the first part. Water gets hot again when diverted back to spout. I have tried various shower heads> They have been both low flow and regular shower heads and work fine on...
  10. Replies
    12
    Views
    5,091

    Ok. But I am getting hot water to the shower....

    Ok. But I am getting hot water to the shower. just not when diverted to shower head.
  11. Replies
    12
    Views
    5,091

    I will try these things shortly. Must add that...

    I will try these things shortly. Must add that all of above is with knob turned all the way to hot. Never in middle. Turning to middle makes it colder then luke warm.
  12. Replies
    1
    Views
    829

    Abandoned Irrigation system

    Just purchased a second home. Yard was trenched to add an irrigation system and some but not all trenches have pvc pipe in them and even some have been capped at specific irrigation sprinkler head...
  13. Replies
    12
    Views
    5,091

    There is no water from spout when the diverter is...

    There is no water from spout when the diverter is engaged to move water to shower head so to answer your question I would say no. But I may not understand what you are asking. Hot at tub spout,...
  14. Replies
    12
    Views
    5,091

    No Hot water from shower head

    Master bedroom tub/shower faucet. Water at spout is plenty hot but when diverter is engaged the water comes out of shower head hot for a very short period of time (less than 30 seconds) and then...
Results 1 to 14 of 14