(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: dunkinidaho; Keyword(s):

Search: Search took 0.35 seconds.

  1. Replies
    3
    Views
    418

    thanks for the advice

    thanks for the advice
  2. Replies
    3
    Views
    418

    Winterizing my softener

    We live in florida in the winter and are wondering if there is anything we should do to our softener for this time. Usually we just turn off the water at the well and leave. When we get home in the...
  3. Replies
    2
    Views
    268

    Thanks for the response, I'll read you the...

    Thanks for the response, I'll read you the analysis off the paper:
    results units DL method reference
    hardness by calculation 340000 ug/L 5000...
  4. Replies
    2
    Views
    268

    Water Softener Issues

    Today I have a question regarding my water softener. I'm not sure I have it set correctly. It is a 40,000 gr. single stage design with 4 stages of cycling. The issue I have surrounds the time I have...
  5. Did the test and it looks like the water level is...

    Did the test and it looks like the water level is where it's supposed to be. Just seems a bit low to me. Thanks for the help

    Dunkinidaho
  6. Help with an old problem, bowl water drops after refill

    I'm sure this has been covered before, maybe recently. After the tank and bowl refills the water level will drop about 1/2-3/4 inch. Vent problem? siphon problem? or could it just be this cheap...
  7. Replies
    2
    Views
    517

    Wife wants the toilet moved

    :Wife wants the toilet moved "over there" so I'm doing it. Now installing the new 3in drain pipe through the floor. Do I cut this off flush with the floor? then glue on the flange? Unfortunately I've...
  8. Replies
    4
    Views
    1,651

    Thanks, it's as I thought. I've installed...

    Thanks, it's as I thought. I've installed blocking in the tub wall today and tomorrow the shower. I will be using copper for the shower outlet and bath spout. The PEX is supply lines only. This is a...
  9. Replies
    4
    Views
    1,651

    Kohler K 304 rough in help

    I'm installing two of these valves in my bath re-do. One in a stand alone 4 piece shower stall and one in a stand alone tub. Question pertains to the shower: Does this valve have to be mounted to...
  10. Replies
    11
    Views
    4,371

    In the Fleck manual it says to take the grains of...

    In the Fleck manual it says to take the grains of the resin tank (40,000) and multiply by 90. That gives a 10% reserve. The result is 36,000 which is then divided by the hardness (34). The result is...
  11. Replies
    11
    Views
    4,371

    I use the pre-filter to cut down on the rust...

    I use the pre-filter to cut down on the rust staining on the house from the sprinkler system, it works.

    The formula is 40,000gr. X 90 divided by 34 = 1060
  12. Replies
    11
    Views
    4,371

    Gary, Here is the info I've found...

    Gary,

    Here is the info I've found regarding my system. My resin tank is 40,000gr. with a Fleck 5600SE valve. I bought the "upgraded" resin. I have a "BIG BLUE" pre-filter right off the well....
  13. Replies
    11
    Views
    4,371

    www.discountwatersofteners.com

    www.discountwatersofteners.com
  14. Replies
    11
    Views
    4,371

    Gary, Let me get this info together...

    Gary,

    Let me get this info together and I'll get back to you. The online supplier was glad to sell but not much on the help.

    brian
  15. Replies
    11
    Views
    4,371

    cycle times for my fleck 5600se

    I've searched the site for an answer but couldn't find one so I'm posting it. I have a Fleck 5600SE V2 single backwash softener with a single tank. I've never felt that I have the "right" times set...
  16. Replies
    2
    Views
    537

    Thanks for the quick reply. Since the tank seems...

    Thanks for the quick reply. Since the tank seems to be set at 33psi I'll reset the pressures to 35/55 and split the difference. I didn't know that the pump could run continuously. I thought it would...
  17. Replies
    2
    Views
    537

    one more well question

    I just reduced the operating pressure of my well from 40/60 to 30/50 which seems to be the recommended setting for my 1/2hp 10GPH red jacket pump. The bladder tank is a 32gal Champion. In the process...
Results 1 to 17 of 17