Search:

Just to clarity, my faucet leaked from the moment I put it in also. I tried flushing it, turning it on and off rapidly, took out the cartridge and did a visual check, etc., nothing worked.

Just...

I installed the Forte widespread about 6 months ago. I had a similar leak on the hot side only. It was barely noticeable except for the stopper being wet. Maybe a drop every hour or so.

I...

I have two Drakes and they both have the notch. I bought them from a plumbing supply house.

The only thing I can think of is that it is a place to put your finger to lift the lid off the tank.
...

browniz,

This is a Kohler Forte K-10272-4G 8" widespread faucet. I don't know what brand/model you have, but this one is set up with no allen screw.

I just took another look to be sure. ;)
...

hj,

I'm not the original poster. I was trying to help kmclisterman and I submitted my reply too soon. Sorry about that. I'll try it again.

I had a similar situation involving a Kohler bathroom...

I actually did try turning it both ways and it wouldn't move. However, I did not want to force it in either direction. At least not until I know for sure which way to turn it. I will check with the...

I determined that the hot side is the one leaking. I tried removing the cartridge using a spark plug socket on a 3/8" socket handle. It fit the nut perfectly. The problem, I could not loosen the...

I was able to unscrew the chrome bonnet to get to the stem. I did it on both sides just to see if I could. Now I need to get a new cartridge from Kohler.
Thank you for that! It saved me a big...

I think you're right. It seems like the whole valve has to be removed. I will go through the warranty process to get the parts I need.

It's obviously disappointing to have a brand new fixture...

I found the link I was looking for.

Thank you for hosting such an excellent site!

http://www.terrylove.com/forums/showthread.php?t=743

I just installed a Kohler Forte K-10272-4CP. It is an 8" spread faucet with separate cold and hot controls. The hot side has a slow drip. I'm assuming it is a cartridge that needs to be replaced....

I am unable to find the link to the installation instructions for the Toto Drake that your son posted some time ago. I recall it included how to sand the inside of the tank where the washers are to...

Thank you for the replies. I am considering a Drake ST743S round bowl. It would give me about the same amount of room I had with the original toilet that was installed when the house was built. Even...

I am updating a half bathroom in my family room. It is approximately 45" wide by 10' deep. The vanity is located at the far end of the room and is the width of the room. The toilet is in the middle...

I've heard of Teflon and Clorox, just not together! ;)
Thanks Terry, I'll look for it.

Terry,
Is the Clorox Teflon bowl cleaner effective in reducing the "streaking" effect that has been referred to? I have never heard of this product. Any downside to this product?

Mine makes a similar sound at the very end of the flush. It seems to be normal, possibly a result of the bowl emptying so quickly.

I can only speak for the Drake regarding this issue. I have had my Drake in use for about 6 months. I have never seen any splashing of water and/or bowl contents during flushing. Everything goes...

Thanks for the reply.
I was concerned that the side of the flange would need some space between the lead and the tile to fit properly.

How much of a gap is required between the floor tile and the lead bend for the toilet? I want to make sure there is enough of a gap to install the closet flange, but not too much to insure proper...

I was basing that on the installation manual from Kohler. Please see Figure 6 on Page 5 by clicking on the link. I says that all four feet must rest on the floor and does not mention a ledger board....

I am in the process of having a cast iron tub installed. Currently, the tub is resting on a ledger board attached to the wall. There are shims under one end of the apron to keep the tub from rocking...