Search:

I did not mean to say to vent it into the soffit. They make a special cover just for a under soffit vent. It vents out each side of the cover. If you have room for the duct in the overhang area they...

I would still think you need the metal washer under the bolt head then the rubber washer so the bolt head does not go thru the rubber washer. As you stated in the post above "I assume it is coming...

Wouldn't this mean that the larger doughnut seal is not set right?

I have used composite shims available at the big box stores.

Yes I did miss that, My area wells run from 45 to 150 ft. or so. Thanks for the correction.

High grade poly is what most use in my area. That way if you have to lift it out to change a submersible pump you just start walking up the street pulling up the poly. Have changed one pump about...

I have installed the type that go under the soffit before and I always use ridged 3 or 4" duct work, That way you don't get it sagging. Also you should insulate the duct if you are in a cold climate...

Here is another washer stand pipe drawing

14008

This is true but in all the basement remodels I have done we now use the add on spreader bars that hook to the grid. They are available for most recessed lights if they don't already come with them....

I think if you click on the full size picture it does look like a "y" that goes up in the foundation. If this is true where does the pipe go up to that would be in the middle of the cement wall?

Thanks for the info guys, I will give these a try. Also "ballvalve", Thanks for the links. That is some great info.
I guess the tank I have is either glass or porcelain lined so I don't think it is...

Hi all,
I have had a electric 28 gallon lowboy water heater that was disconnected and empty about two years at my beach house and now I have been flushing it with fresh water and was wondering if...

What ?????????

If you are saying that it should use the rest of the water in the tank I think that is wrong. The newer tanks only use part of the water in the tank as per design. If it is working fine why would you...

This is how they work. Most toilets that I have seen lately work the same way. They need the height of the water to get the full flush but do not need all of the water which is how it saves water...

I think he need a 5/8 size nut.

Thanks jimbo, The lav sink connects to the 3" pipe as it is going to the sewer with it's own vent. Actually were in my picture above when the 3" 90's to the sewer there is a cleanout there . The 90...

I might not have said that part right. The pipe goes up from the 3" to a Sani-T straight up to the roof. Off of the Sani-T is the trap that goes to the washer stand pipe. Would this be OK? How does...

I have attached a drawing (part borrowed from another post) to show what I have planed.
I have a toilet and was wondering if it needed a vent? It goes down just below the floor joist and bends to a...

Did you take the strainer out and disconnect the drain to this tub before the picture was taken?

We just went through this a few weeks ago. Look into the sump pit and watch the water level. If it is going down while the pump is running to where the pump shuts off and the pit fills up rapidly...

If you are thinking of getting a new 100 amp box, Most of the time the only difference in changing out the 100 and going with a new 200amp might be the down feed wire and meter box. Price should not...

My condensate drain just runs into my utility sink just like you would run a washer drain hose.

If there is no water flowing in are you sure there is water coming out of the manifold where you connected the washer? Also since you just have the cold connected make sure that the connection on the...

Is it possible that they have a box that just has not been used so the test plug has not been removed yet?
Is there room next to the valves that you hooked the water up to?
Can you post a picture...