(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: buzzard; Keyword(s):

Search: Search took 0.13 seconds.

  1. Thread: solder

    by buzzard
    Replies
    3
    Views
    1,198

    solder

    i have a full spool of solder thats been in the garage for i dont know how long.

    it is dutch boy and has the following markings:

    Sn 95% Sb 5% also says ASTM B-32.

    i also have a half...
  2. Replies
    2
    Views
    863

    copper size/design

    new construction. no copper in yet. crude sketch of house.

    i am getting ready to do copper water supply and am unsure on sizing.

    i have drawn dark blue for 3/4" and light blue for 1/2"( cold...
  3. Thread: venting

    by buzzard
    Replies
    2
    Views
    741

    venting

    gentlemen, a question for your expertise.

    i have two vents up to the ceiling/attic floor represented by the two red lines in the picture. i have drawn three proposed spots to take it through the...
  4. Replies
    3
    Views
    9,745

    this is how i propose to put it together. is...

    this is how i propose to put it together. is there a better way? will it meet IRC code?

    http://i277.photobucket.com/albums/kk73/buzzardchess/mess5.jpg
  5. Replies
    3
    Views
    9,745

    1st floor plumb layout revised

    would like some thoughts on the proposed layout..


    http://i277.photobucket.com/albums/kk73/buzzardchess/plumblayout9.jpg
  6. Replies
    23
    Views
    4,440

    i hope he made that number up. i glued it. :(

    i hope he made that number up. i glued it. :(
  7. Replies
    23
    Views
    4,440

    thanks for all this info. im took all those notes...

    thanks for all this info. im took all those notes down. someone else wrote that i need ten pipe diameters from the soil stack to the lav connection in pic 4. is that the case?
  8. Replies
    23
    Views
    4,440

    all pipes shown are 4" or 2"

    all pipes shown are 4" or 2"
  9. Replies
    23
    Views
    4,440

    i re-read westcoasts last post and i'm wondering...

    i re-read westcoasts last post and i'm wondering if it's being suggested that a longsweep 90 with a straight verticle to the flange is a better way to do that?

    also i put the cleanouts (pic 1)at...
  10. Replies
    23
    Views
    4,440

    im pitching it too much cause i dont know any...

    im pitching it too much cause i dont know any better :D. i have been lurking here for days waiting for a good man like you to say " look here, chief, try running the poop a little slower with less...
  11. Replies
    23
    Views
    4,440

    thanks for the feedback. i plan on putting a...

    thanks for the feedback. i plan on putting a 4x4x2 wye for the toilet vent and joining it to the shower vent at over 42". this make sense? does it matter where along that short toilet branch i put...
  12. Replies
    23
    Views
    4,440

    u r right. that 1/8 bend is half way in concrete....

    u r right. that 1/8 bend is half way in concrete. i just made the note and will space that out, thanks. i'd like to hear some feedback on the toilet branch. i have some concerns there. like, should...
  13. Replies
    4
    Views
    1,296

    power flickering

    so the power is flickering this morning and i went outside after checking service panel. the meter socket ( old round kind) is making sizzling sound and its fogged up inside. so im thinking the...
  14. Replies
    23
    Views
    4,440

    i wanna say they are 16" or so from top of...

    i wanna say they are 16" or so from top of horizontal to top finish floor. with the washer horizontal being about 6" from top to top.
  15. Replies
    23
    Views
    4,440

    closet flange is 16" to center from wall ( that...

    closet flange is 16" to center from wall ( that is side to side). it will be 12.5" to center behind toilet on future frame wall. this is a rough for a future basement bath and there will be no finish...
  16. Replies
    23
    Views
    4,440

    thank u for response. its a bathroom sink that...

    thank u for response. its a bathroom sink that sits just above image. i hadnt thought of joining the washer and sink. i will put that long sweep 90 on there, didnt think of that either. i appreciate...
  17. Replies
    23
    Views
    4,440

    rough in help. pics included

    i posted last week with sketches. i went ahead and DRY fitted the pipes for better image. i am under irc code. is there anything here that is not legal under that code or that will not work properly?...
  18. Replies
    16
    Views
    4,482

    we are under irc code

    we are under irc code
  19. Replies
    16
    Views
    4,482

    me again. i just have to ask. i pestered a...

    me again. i just have to ask. i pestered a plumber at the job today ( im a bricklayer) and he took a look at my sketches and he said " the toilet, the lav and the shower dont need a vent. they are...
  20. Replies
    16
    Views
    4,482

    ok. i corrected the washer setup. eliminated the...

    ok. i corrected the washer setup. eliminated the drain. i thought a basement drain was required by code. if it is. maybe i can run seperate like in drawing 1 with a vent. also i provided more detail...
  21. Replies
    16
    Views
    4,482

    ok. i added a side view. i have no illusions of...

    ok. i added a side view. i have no illusions of ending up on the front cover of plumbers life. i know the drawings crude. i just wanna get an idea if im on the right track. will it work? will it work...
  22. Replies
    16
    Views
    4,482

    help with basement rough in. pics included

    ok. im looking to rough in the basement plumbing so i can get my floor poured. can you pro's look over this mess and see if this will work. i forgot to include the vent for the floor drain. maybe i...
Results 1 to 22 of 23