(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: bmaker; Keyword(s):

Search: Search took 0.13 seconds.

  1. Replies
    16
    Views
    1,889

    Probably not, since the switch is over by the...

    Probably not, since the switch is over by the back door, several feet from the sink. The more I think about this, the more I'm thinking it must be either a switched outlet or a circuit in the...
  2. Replies
    16
    Views
    1,889

    Hah! Best suggestion yet. I'll do that after...

    Hah! Best suggestion yet. I'll do that after trying the other ones above!
  3. Replies
    16
    Views
    1,889

    No garbage disposal but there was an in-counter...

    No garbage disposal but there was an in-counter blender thingy that we got rid of. I checked that circuit but alas it was fed from a different breaker.
  4. Replies
    16
    Views
    1,889

    There is a ceiling light but not a fan. Perhaps...

    There is a ceiling light but not a fan. Perhaps there used to be. Will check out this option.
  5. Replies
    16
    Views
    1,889

    I checked some of the duplex outlets but maybe...

    I checked some of the duplex outlets but maybe not all. Will try that.
  6. Replies
    16
    Views
    1,889

    Oh where, oh where does that circuit go?

    Doing a bit of remodeling on my daughter's kitchen. They have a switch on the wall that doesn't seem to control anything, although I can tell it is wired up to a hot circuit. I've checked all the...
  7. Four fixtures @ 13w ea = 52w. All done. Looks...

    Four fixtures @ 13w ea = 52w. All done. Looks great!
  8. I appreciate your thoughts on this. I'm hoping...

    I appreciate your thoughts on this. I'm hoping you're right. But I want to make sure it's safe and code-compliant since it's my daughter's house!
  9. Thanks for the reply! Is the code concern that...

    Thanks for the reply! Is the code concern that the "over the counter top" outlet is on a 20 amp breaker and lights only need 15 amp? Other than that I couldn't imagine that the NEC would care...
  10. Controlling under-cabinet fluorescent fixtures with a wall switch

    I just installed a set of 4 under-cabinet fluorescent fixtures. These are GE's with T5 tubes. The fixtures come with a 3-prong plug so they have to be plugged in to their own receptacles or daisy...
  11. Replies
    23
    Views
    4,327

    Here's what I did on that. I removed the float...

    Here's what I did on that. I removed the float and suction tube assembly from the sleeve in the salt tank. I then took it up to the kitchen when my wife wasn't around and dipped it into a pitcher...
  12. Replies
    23
    Views
    4,327

    Got the resin installed, put everything back...

    Got the resin installed, put everything back together, flushed out the whole system (took about 10 minutes at about 3-4 gpm), then did a regen for good measure. Unfortunately, the brine still will...
  13. Thread: Water too high

    by bmaker
    Replies
    16
    Views
    2,714

    I wouldn't worry about removing the water from...

    I wouldn't worry about removing the water from the brine tank unless it is in danger of overflowing. If it works the same as mine does, the float in the brine tank should shut off the water when it...
  14. Replies
    23
    Views
    4,327

    Well, I bought a set of seals for a Fleck 25x0...

    Well, I bought a set of seals for a Fleck 25x0 and they are too small. The GI seals are 1 3/8" OD and 1 1/8" ID; the Flecks are 1 1/4" OD and 1" ID. The opening in the valve body after taking off...
  15. Replies
    23
    Views
    4,327

    Didn't want to tear the front controller off to...

    Didn't want to tear the front controller off to get this pic. Have done it before and I know the valve piston is a light green color. I'll see what I can find at a local dealer for the Fleck 25x0. ...
  16. Replies
    23
    Views
    4,327

    I measured as you suggested. Not exact due to...

    I measured as you suggested. Not exact due to the difficulties of getting my calipers in there, but I would say it's pretty close to 1 3/4". Perhaps a hair or two larger. This is at the flared out...
  17. Replies
    23
    Views
    4,327

    Here are a few photos of my valve. Can you tell...

    Here are a few photos of my valve. Can you tell which one it is?
    14945
    14946
    14947
  18. Replies
    23
    Views
    4,327

    Where can I get a set of seals and, more...

    Where can I get a set of seals and, more importantly, the special tools (seal hook, puller, and stuffer) needed to remove and re-install them (which I will need even if I just swap them out as you...
  19. Replies
    23
    Views
    4,327

    General Ionics IQ0820B won't draw brine

    I have a 20 year-old GI unit that worked well until last month. During the regen cycle, when it gets to the brine draw step there is no vacuum on the brine draw tube. In fact, it actually leaks a...
Results 1 to 19 of 19