(206) 949-5683, Top Rated Plumber, Seattle

Search:

Type: Posts; User: bbbluueyes; Keyword(s):

Search: Search took 0.13 seconds.

  1. Replies
    0
    Views
    619

    Small air filter source

    Hi there - thank you in advance for any advice you may have.

    I have a wall heater from a 1960's apartment building that needs a smaller air filter -

    The size is 6 1/2 x 12 x .5 inches.
    ...
  2. Replies
    7
    Views
    2,517

    Pipe

    Thanks again for the reply- I am at a different location from the problem pipe so I will try tomorrow - do you think it is ok if I can only get about 1" of the pipe out of the wall and leave the rest...
  3. Replies
    7
    Views
    2,517

    Pipe

    Thanks guys for replying. The pipe is just the "typical" drain pipe secured by a washer on the wall. I tried the screwdriver - very difficult ---- were you talking about using a hacksaw blade to...
  4. Replies
    7
    Views
    2,517

    Drain pipe stuck in wall...

    Hi- thank you very much in advance-
    While removing an old (i.e. 60's) bathroom sink and faucet, the pipe going into the wall would not come out. After tugging, cutting, etc.. the pipe old pipe,...
  5. Replies
    12
    Views
    2,805

    Thanks

    Thanks for the responses - i will give it a shot !
  6. Replies
    12
    Views
    2,805

    Removal of Bathtub Drain Piece

    Hi - thanks in advance for any advice.

    I am trying to remove a bathtub drain piece(on the floor of the bathtub) in order to install a new overflow piece and drain piece.

    Is there a special...
  7. Replies
    4
    Views
    2,300

    Tub Spout Rough In

    Hi there - thank you in advance ~
    Should be a fairly easy question - I am installing a new tub spout in a remodeled bath. I had a plumber install a new shower valve - for the tub spout rough in,...
  8. Installing new soap dish into existing ceramic tile

    Hi - thank you in advance for any advice....

    I am replacing an existing built in soap dish with a new soap dish. The soap dish is built into the wall.....

    - need to grind or cut existing...
  9. Toro Mini 8 sprinkler head will not rotate

    Hi - as the title implies, my toro mini 8 sprinkler head will not rotate...I have cleaned around it...any suggestions would be great!

    Thank you.
    Paul
  10. Replies
    18
    Views
    12,574

    Schlage deadbolt-flush screws

    Hi - I am trying to remove a what I think is a Schlage deadbolt. From the inside of the lock, instead of phillps screws or flat screws, the "screws" are entirely flush to the lock. The face of the...
  11. it wasnt the aerator, I am going to work on it on...

    it wasnt the aerator, I am going to work on it on Sat...
  12. thank you, I will give her a try...Paul

    thank you, I will give her a try...Paul
  13. yes, I bought two new ones...I am wondering if I...

    yes, I bought two new ones...I am wondering if I installed them too deep....
  14. Crane Dial Ease Replacing - Bathroom Faucet

    Hi , I am trying to fix a dripping crane bathroom faucet...I had two dial ease (the #4 on the picture) parts on hand so I thought I would replace both...

    1. I have proper water connections and...
  15. Replies
    4
    Views
    1,864

    yes, replacing both dial eze valves

    yes, I am replacing both of the dial eze valves....the entire bronzish piece that screws in from the top of the faucet.

    after replacing both dial ease and turn on the water from the supply below,...
  16. Replies
    4
    Views
    1,864

    1960's Crane Bathroom Faucet

    I am trying to replace the entire stem on both of the hot and cold water...

    1. Water is hooked up fine, if stems are off and water is turned on there is pressure
    2. When I put both of the stems...
Results 1 to 16 of 16